Fluke DATAPAQ XDL12 User Manual Download Page 4

Page: 4 / 38

Datapaq Ltd. makes no representations or warranties of any kind

whatsoever with respect to the contents hereof and specifically

disclaims any implied warranties of merchantability or fitness for any

particular purpose. Datapaq Ltd. shall not be liable for errors

contained herein or for incidental or consequential damages in

connection with the furnishing, performance or use of the Datapaq

software, associated hardware or this material.

Datapaq Ltd. reserves the right to revise this publication from time to

time and to make changes to the content hereof without obligation to

notify any person of such revisions or changes.

Datapaq, the Datapaq logo and Oven Tracker are registered

trademarks of Datapaq. Microsoft and Windows are

registered trademarks of Microsoft Corporation.

Manual set in 10 pt Gill Sans.

User manuals are available in other languages;

contact Datapaq for details.

SAFETY WARNINGS

For safe use of Datapaq equipment, always:

Take care to follow its supplied instructions.

Observe any warning signs shown on the equipment itself.

Indicates

potential hazard

On Datapaq equipment this normally warns of high
temperature, but where you see the symbol you should
consult the manual for further explanation.

Warns of

high temperatures

Where this symbol appears on Datapaq equipment, the
surface of the equipment may be excessively hot (or
excessively cold) and may thus cause skin burns.

Summary of Contents for DATAPAQ XDL12







































Search results

Summary of Contents for DATAPAQ XDL12

Reviews:

Related manuals for DATAPAQ XDL12

Brands by name

Popular brands

Fluke DATAPAQ XDL12, User Manual

Search results

Summary of Contents for DATAPAQ XDL12

Reviews:

Related manuals for DATAPAQ XDL12

Brands by name

Popular brands