manualshive.com logo in svg

Fluke CableAnalyzer DSX-602, User Manual

Share
Download
Fluke CableAnalyzer DSX-602 User Manual Download Page 40

DSX-602 CableAnalyzer

Users Manual

32

Table 2. Settings for Twisted Pair Tests 

Setting

Description

Cable Type

Select a cable type that is correct for the type you will 
test. To see a different group of cable types, tap 

MORE

, 

then tap a group. To make a custom cable type, tap 

Custom

 in the 

Cable Groups

 list.

NVP

Nominal velocity of propagation. The tester uses the NVP 
and the propagation delay to calculate the length of the 
cable.
The default value is defined by the selected cable type 
and is the typical NVP for that cable type. To enter a 
different value, tap the 

NVP

 panel, then tap

 

 or 

 

on the 

NVP

 screen to increase or decrease the value. 

To find the actual value for a cable, connect a known 
length of the cable to the tester, tap 

MEASURE

 on the 

NVP

 screen, then change the NVP until the measured 

length matches the known length. Use a cable at least 
30 m (100 ft) long.
When you increase the NVP value, the calculated length 
increases.

Shield Test

This setting shows only when you select a shielded cable 
type. 

On

: The wire map test includes a DC test for shield 

continuity and AC tests for shield quality. The wire map 
test fails if the shield is open or the AC test results are 
unsatisfactory. 

Off

: The wire map shows the shield if the shield has 

continuity. The tester does not do AC tests for shield 
quality. The wire map test does not fail or show the 
shield if the shield is open.

Test Limit

Select the correct test limit for the job. To see a different 
group of limits, tap 

MORE

, then tap the name of a 

group. 

Summary of Contents for CableAnalyzer DSX-602















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands