background image

LIMITED WARRANTY AND LIMITATION OF LIABILITY 

This Fluke product will be free from defects in material and workmanship for three 
years from the date of purchase. This warranty does not cover fuses, disposable bat-
teries, or damage from accident, neglect, misuse, alteration, contamination, or abnor-
mal conditions of operation or handling. Resellers are not authorized to extend any 
other warranty on Fluke’s behalf. To obtain service during the warranty period, contact 
your nearest Fluke authorized service center to obtain return authorization information, 
then send the product to that Service Center with a description of the problem. 
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS 
FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE 
IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUEN-
TIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since 
some states or countries do not allow the exclusion or limitation of an implied warranty 
or of incidental or consequential damages, this limitation of liability may not apply to 
you. 
 

Fluke Corporation 
P.O. Box 9090 
Everett, WA  98206-9090 
U.S.A. 

Shanghai Shilu Instrument Co., Ltd. 
#139, 2638 Nong, Hongmei Nanlu 
Shanghai 201108 
Biao Zhun Hao: Q/SXAV 1-2002 

11/99 

Summary of Contents for 116C

























Reviews: