background image

21

AUTOMATIC WORKING MODE/STOP

 • Same function as “AUTO/STOP” button on bidet base.
 • Press once to start automatic cleaning. Press once during any cleaning cycle to stop cleaning and retract  
  the wand.
  •  15 seconds of rear cleaning at fixed position > 60 seconds of oscillate cleaning > 30 seconds of rear    
    cleaning at fixed position > 120 seconds of DRY. Press ”AUTO/STOP” to end the cycle at any time.

REAR/OSCILLATE CLEANING

  •  Press for posterior cleaning. While in rear cleaning mode, press the button again to oscillate the wand.
  •  15 seconds of posterior cleaning at fixed position > 60 seconds of oscillate cleaning > 15 seconds of fixed  
    position cleaning > 120 seconds of DRY. Press ”AUTO/STOP” to end the cycle at any time.

FRONT/OSCILLATE CLEANING

  •  Press once to enter front cleaning mode. While in front cleaning mode, press the button to oscillate the wand.
  •  15 seconds front cleaning at fixed position > 60 seconds of oscillating cleaning > 15 seconds front  

 

    cleaning at fixed position > 120 seconds of DRY. Press ”AUTO/STOP” to end the cycle at any time.

GENTLE CLEANING

  •  Press once to bring both water temperature and water pressure to the lowest level. Drying at the lowest  
    level will begin automatically once cleaning cycle ends. Recommended for children, elderly, patients,    
    those who are physically limited, cannot adjust the temperature or have sensitive skin.
  •  15 seconds of cleaning at fixed position > 60 seconds of oscillate cleaning > 30 seconds of fixed position  
    cleaning > 2 minutes of level 1 DRY. Press ”AUTO/STOP” to end the cycle at any time.

DRY

  •  Press once to begin drying.
  •  5 minutes of warm, dry air. Stops at any time user leaves the seat. Press “AUTO/STOP” to end the cycle at  
    any time. See Page 22. below for temperature control information.

NIGHT-LIGHT

  •  Automatically illuminates when the room goes dark and shuts off when the light comes on.
  •  To manually turn light off, hold button until you hear a short “ding” and the light goes out.
  •  To manually turn the light on, hold button again until you hear another “ding” and the light comes on.

DEODORIZER

  •  Activates the charcoal filter to draw in fumes and eliminate odor.
  •  Automatically activates when you sit down and will stop when the the “FRONT” or “REAR” wash cycles  
    start, you press the “AUTO/STOP” button or about 60 seconds after you stand up.
  •  To manually shut off deodorizer, hold button until you hear a “ding.”
  •  To turn deodorizer back on, hold button until you hear another “ding.”

POSITION

  •  Press to adjust the wand between five different positions while in the rear or front cleaning modes  

 

    until you reach your desired position.

Remote Control Functions:

Summary of Contents for soft spa 9500

































Reviews: