Flowserve SEM-100SS Installation Operation & Maintenance Download Page 17

Page: 17 / 22

Flowserve.com 17

PUIOM000649-00-UIM (EN/AQ)

August 2022

SEM-100SS User Instructions

6. Parts List and Parts Diagram

SEM-100SS Parts List

Qty.

Part No.

Description

DD6P-46A

SS Phillips Head Screw, 10-24 X .75”

S10-11B COMPLETE

Electronic Assembly

S10-06SS

Meter Gasket

SFM10000-19

SS Screw, Short

SFM10000-14A

Meter Plate

NUT-02

10-24 Lock Nut

SFM10000-10B

Magnet Holder

SFM10000-18

Viton O-Ring

SFM10000-06

Screws

SFM10000-05

Mounting Bracket

SFM10000-07

Washer

SFM10000-08

Drive Dog Assembly

SFM10000-02

Top Wobble Housing

SFM10000-03A

Wobble Plate Assembly

SFM10000-20

Nut

SFM10000-14A

Meter Plate

SFM10000-13A

SEM-100SS 316SS Fluid Housing

Note:

All parts are common to the SEM-100 and SEM-100FT except for the fluid housing

Summary of Contents for SEM-100SS























Search results

Summary of Contents for SEM-100SS

Reviews:

Related manuals for SEM-100SS

Brands by name

Popular brands

Flowserve SEM-100SS, Installation Operation & Maintenance

Search results

Summary of Contents for SEM-100SS

Reviews:

Related manuals for SEM-100SS

Brands by name

Popular brands