manualshive.com logo in svg

FlowLine EchoSwitch II LU77 Series, Manual

Share
Download
FlowLine EchoSwitch II LU77 Series Manual Download Page 14

14 of 33 

EchoSwitch II 

09 JUL 08 

 MN300650 

Rev 

A 

How to enter the MENU 

1.

 

Press and hold SELECT key (approximately 5 seconds) until MENU is displayed. 

2.

 

The menu items will rotate through display. 

3.

 

Press SELECT to change an item. 

 

 

 

 
How to configure UNITS 

1.

 

In the MENU mode, press select when UNITS is display. 

2.

 

Press SELECT to choose between INCHES, CM (centimeter), FEET, METERS or 
PERCENT. 

3.

 

Select EXIT to return to the Top Level Menu. 

 

Note:  Reading the level of liquid in Percent 

•

 

Flowline recommends that when selecting PERCENT, configure the Height and Fill_H 
settings before selecting PERCENT in order to span the EchoSwitch II for your 
application requirements. 

•

 

When in PERCENT, the operational span will be based upon the last TANK settings, 
typically the factory settings for Height and Fill_H. 
   

EchoSwitch II 

Height 

Fill_H 

LU77 Series 

98.4” (250 cm) 

94.4” (239.8 cm) 

LU78 Series 

295.2” (750 cm) 

287.2” (729.7 cm) 

 

•

 

When PERCENT is selected, the TANK settings (Height and Fill_H) will be disabled.   
 

Summary of Contents for EchoSwitch II LU77 Series


































Reviews:

No comments

Brands by name

Popular brands

Load more brands