manualshive.com logo in svg

FlowLine EchoSwitch II LU77 Series, Manual

Share
Download
FlowLine EchoSwitch II LU77 Series Manual Download Page 13

 

09 JUL 08 

EchoSwitch II 

13 of 33 

Rev A 

MN300650  

Feature Guide 

FEATURE 

  

ACCESS 

BY 

Easy to use MENU 

Press and hold SELECT key until MENU is displayed 
approximately 5 seconds.  The menu items will rotate 
through display, press SELECT to change an item. 

Many UNITS of 
measurement. 

In the MENU mode, press select when UNITS is display, 
then select INCHES, CM (centimeter), FEET, METERS 
or PERCENT. 

No cumbersome measure 
required.  Set point 
distances are relative to the 
tank bottom. 

In MENU mode, select the TANK item and set the 
HEIGHT of the tank from the transducer face to the 
bottom of the tank.  Set the Fill Height (FILL-H) to the 
maximum fill height of the liquid from the bottom of the 
tank.  Now all of the set points are from the bottom of the 
tank up. 

Easy PUMP programming 

In MENU mode, when the relay you wish to program is 
showing, press SELECT, then select PUMP, then FILL 
or EMPTY, then set the ON or OFF points.  The DELAY 
is a start pump delay used in batch processing 
applications. 

DELAY Pump turn on. 

In MENU mode, select relay and set the pump actions 
desired, when the DELAY menu item is displayed press 
and set the turn on delay time in seconds.  The pump will 
now delay after the set point is reached before turn on. 

Easy ALARM 
programming 

In MENU mode, when the relay you wish to program is 
showing, press SELECT, then when ALARM appears 
select it, then select HIGH or LOW, then set the ON 
point.  The hysteresis (HYSTER) sets the OFF point the 
distance set in HYSTER away form the ON point. 

Easy ALTERNATE with 
DUPLEX and TRIPLEX 
pumps 

Just program the least two relays as pumps and the M-
PLEX menu item will appear in the top menu, select it 
and then select either NO ALT (No alternation), 
DUPLEX (two pumps) or TRIPLEX (three pumps). Note 
you can have three pumps programmed and only duplex 
two of them.  This is useful during servicing. 

TIMED BASED 
ALTERNATE pumps 

In MENU mode, program at least two relays as pumps 
and select M-PLEX menu.  Select either DUPLEX or 
TRIPLEX and then select A-TIME.  Change the values 
(in hours) to the time you which the pumps to alternate.  
The cycle-by-cycle alternation will be disabled and the 
time base will take over. 

 

 

Summary of Contents for EchoSwitch II LU77 Series


































Reviews:

No comments

Brands by name

Popular brands

Load more brands