manualshive.com logo in svg

FlowCon SM.3, Installation And Operation Instruction Manual

Share
Download
FlowCon SM.3 Installation And Operation Instruction Manual Download Page 5

P1

P2

Black

Red

FlowCon Intelligent Interface    

Black

Green

White

Red

White

Green

Red (no function)

White/Black - Ground/common

Red - Power 24V DC

FlowCon Pressure Sensors    

FlowCon Temperature Sensors    

Black

Red

FlowCon Intelligent Interface    

White

Green

Red (no function)

Black

Green

White

Red

White/Yellow - Input 0-5VDC

Black - Ground/common

Red - Power 24V DC

T1

T2

Start-Up Sequence

When power is turned on, the actuator will auto-

matically calibrate to determine closing point of 

the valve. Calibration can take up to 10 minutes 

depending on the valve’s position at start-up. 

During calibration actuator display will show 

“

CAL

”. Hereafter it will procced to normal opera-

tion mode (according to control signal).

If no control signal is detected, flush is started if 

enabled in the programming menu (enabled by 

default), opening the valve to 5/6 of fully open. 

Actuator display will show “

FLUSH

” until control 

signal is detected.

At first start-up please enter programming menu 

to set actuator settings.

FlowCon FIT 65-250 mm (2 1/2”-10”)

1B95095 - 02/2020

This paper is a supplement to the

 FlowCon General Instruction 

Latest release of any FlowCon material is available on

 

www.flowcon.com

Page 5 of 10

Summary of Contents for SM.3











Reviews:

No comments

Brands by name

Popular brands

Load more brands