background image

427-0100-00-12 Version 100

December 2018

2

The information contained herein does not contain technology as defined by EAR,15 CFR772, is publicly available, and therefore not subject to EAR.

© 2018 FLIR Systems, Inc. All rights reserved worldwide. No parts of this manual, in whole or in part, may be 

copied, photocopied, translated, or transmitted to any electronic medium or machine readable form without the 

prior written permission of FLIR Systems, Inc.
Names and marks appearing on the products herein are either registered trademarks or trademarks of FLIR 

Systems, Inc. and/or its subsidiaries. All other trademarks, trade names, or company names referenced herein are 

used for identification only and are the property of their respective owners.
This product is protected by patents, design patents, patents pending, or design patents pending.
Photographs and images appearing in this manual may have been modified for illustrative purposes using 

commercial image editing software and may not always reflect an actual product configuration. 

The contents of this document are subject to change without notice. 

For additional information visit 

www.flir.com

 or write to FLIR Systems, Inc.

FLIR Systems, Inc.

6769 Hollister Avenue

Goleta, CA 93117
Support: 

https://www.flir.com/support-center/support-hq/

.

Important Instructions and Notices to the User:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This 

device may not cause harmful interference, and (2) this device must accept any interference received, including 

interference that may cause undesired operation.
Modification of this device without the express authorization of FLIR Systems, Inc. may void the user’s authority 

under FCC rules to operate this device.

Note 1:

 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to 

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference 

when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate 

radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful 

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful 

interference in which case the user will be required to correct the interference at the user’s own expense.

Note 2:

 If this equipment came with shielded cables, it was tested for compliance with the FCC limits for a Class A 

digital device using shielded cables and therefore shielded cables must be used with the device

Industry Canada Notice

This Class A digital apparatus complies with Canadian ICES-003.

Avis d’Industrie Canada

:

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Proper Disposal of Electrical and Electronic Equipment (EEE)

The European Union (EU) has enacted Waste Electrical and Electronic Equipment Directive 2002/

96/EC (WEEE), which aims to prevent EEE waste from arising; to encourage reuse, recycling, and 

recovery of EEE waste; and to promote environmental responsibility.
In accordance with these regulations, all EEE products labeled with the “crossed out wheeled bin” 

either on the product itself or in the product literature must not be disposed of in regular rubbish bins, 

mixed with regular household or other commercial waste, or by other regular municipal waste 

collection means.  Instead, and in order to prevent possible harm to the environment or human 

health, all EEE products (including any cables that came with the product) should be responsibly 

discarded or recycled.

To identify a responsible disposal method nearby, please contact the local waste collection or recycling service, the 

original place of purchase or product supplier, or the responsible government authority in the area. Business users 

should contact their supplier or refer to their purchase contract.

Document History

Version

Date

Comment

100

December 2018 Initial release of Saros Dome camera with video analytics intrusion detection

Summary of Contents for Saros








































Reviews: