background image

1.1

CONDITIONS OF INSTALLATION

In Great Britain :-

It is law that all gas appliances are installed only by a GAS SAFE registered

installer in  GB, in accordance with these installation instructions and the Gas

Safety (Installation and use) Regulations 1998. Failure to install appliances 

correctly could lead to prosecution. It is in your own interest and that of safety to

comply with the law.

The installation must also be in accordance with all relevant parts of the Local and

National Building regulations where appropriate, the Building Regulations

(Scotland Consolidation) issued by the Scottish Development Department, and all

relevant recommendations of the following British Standard Code of Practice, and

in accordance with the latest IEE Wiring Regulations.

1.

B.S. 5871.  Part 1. Installation of Gas Fires.

2.

B.S. 5440.: 2000  Parts 1 & 2.  Installation of Flues & Ventilation.

3.

B.S. 6891.  Installation of Gas Pipework.

4.

B.S. 6461.  Part 1.  Installation of Chimneys & Flues.

5.

B.S. 1251.  Open Fireplace Components.

6.

B.S. 715.    Metal Flue pipes for Gas Appliances.

7.

B.S. E.N. 1858   Clay Flue blocks and Terminals.

8.

B.S. 7566   Installation of factory-made Chimneys.

Ventilation Requirements

For use in G.B. purpose built ventilation is not normally required for this

appliance.

In Republic of Ireland :-

For use in I.E. this appliance must be installed in accordance with the rules

in force by a competent person and used only in a sufficiently ventilated

space.  Please consult document  

I.S. 813 : 1996 Domestic Gas Installation

,

issued by the National Standards Authority of Ireland.

1.2

FLUE AND CHIMNEY SUITABILITY

The appliance is designed for use with conventional brick built chimneys or lined

chimneys and pre – fabricated flues. It is also suitable for use with pre-cast flue

blocks conforming to BS EN 1858 and metal flue boxes conforming to BS 715. All

flues must conform to the following minimum dimensions.

Minimum diameter of circular flues

125 mm 

Minimum effective height of all flue types

3 metres

Minimum cross sectional area of Pre-cast Flues

122.7 cm2

4

Summary of Contents for FWER EN Sereis






























Reviews: