background image

Manual Flamcomat MK-U G4

We reserve the right to change designs and technical specifications of our products.

11

ENG

The maximum pressure of system water in conducting components may be equal to the maximum set pressure for 
the applicable safety valve. 

Safety valve max. 6; 10 or 16 bar. Use of eye/face protectors is required if the eyes or face could be injured by flying parts or 
spraying fluids.

To stop electrical equipment (control unit, pumps, valves, peripheral equipment), cut power to the control unit. The power 
supply must remain off for the period of the work.

It is forbidden to alter or use non-original components or replacement parts without authorisation. Such acts may result 
in serious personal injury and endanger operational safety. They will also render any claim for damages against product 
liability void.

It is recommended to contact Flamco Customer Service for carrying out these services.

4.19 Obvious misuse

 •

Operation at incorrect voltage and/or frequency.

 •

Use in inappropriate system designs.

 •

Use of unpermitted installation materials.

4.20 Other hazards

 •

Overload of construction parts by the presence of unpredictable extreme values.

 •

Operational continuity at risk in the case of changed, non-permissible ambient conditions.

 •

Operational continuity at risk in the case of safety-control parts being taken out of service or malfunctioning.

Summary of Contents for Flamcomat MK-U G4





































Reviews: