- 28 -
TROUBLE SHOOTING GUIDE
1.
No display on the console after the power is started:
The probable reason is that the wire from the console to the bottom
control board is not connected well or the transformer is burnt out. Take off
the upright frame tubes and check every single connection part of the
wires from the console to the bottom control board and make sure that all
the wires are connected well. If the problem is caused by the defective
wires or the defective transformer, please do the replacement by the new
wires or transformer.
2.
E01—Communication failure:
The probable reason is that the communication from the console to the
bottom control board is
stuck.
Check every single connection part of the
wires from the console to the bottom control board and make sure that all
the wires are connected well. If the problem is caused by the defective
wires, do the replacement by the new wires.
3.
E02—Burst clash protection:
Check if the voltage is lower than 50% of the normal voltage and do the
testing again by the correct voltage. Check if the control board has strange
smell, if it is, please use a new control board to do the replacement. Check
if the motor wires are connected well, and re-connect the motor wires well.
4.
E03—No sensor signal:
The probable reason is that the speed sensor signal has not been received
during 10 minutes, check if the sensor signal light of the bottom control
board is flashing, if not, please use the new part to do the replacement.
Check if the sensor plug is connected well or if the magnetic sensor is
broken, re-connect the sensor plug or change the magnetic sensor with
the new one.
5.
E04—Incline leaning failure:
Check if the VR wire of the incline motor is connected well, re-connect the
VR wire plug. Check if the AC wire of the incline motor is connected well,
connect the AC wire of the incline motor with the correct position of the
control board. Check if the motor connection wires are broken, if yes, do
the change by the new wires or the new incline motor. Press the button of
the bottom control board to re-work after all the checkings are done well.
6.
E05—Current overload protection:
The probable reason is that the user’s weight is over limit loading and
Summary of Contents for Miracle V380
