background image

Lit. No. 95902/95903, Rev. 01 

June 15, 2008

Gasoline Warning 
Label (on Engine 
Cover)

SAFETY INFORMATION

Warning/Caution Label

68595

WARNING

CAUTION

•  DO NOT EXCEED GVWR OR GAWR WITH SPREADER AND LOAD.
•  TURN OFF SPREADER BEFORE FILLING, ADJUSTING, OR CLEANING.
•  BYSTANDERS TO STAY A MINIMUM OF 25 FEET AWAY FROM 

OPERATING SPREADER.

•  DO NOT CLIMB INTO OR RIDE ON SPREADER.
•  KEEP HANDS, FEET, CLOTHING AWAY FROM MOVING CONVEYOR 

AND SPINNER.

•  READ OWNER'S MANUAL AND ENGINE MANUAL BEFORE      

OPERATING OR SERVICING SPREADER.

•  EMPTY AND CLEAN SPREADER AFTER EACH USE.

Gasoline Warning Label

Warning/Caution Label

Warning/Caution Label

WARNING

Gasoline is flammable.

•   Turn off engine and allow it to cool before filling gas tank.

•   DO NOT smoke or use open flame within 25 feet of spreader.

•   Allow spilled gas to evaporate completely before starting engine.

•   Gasoline engine produces poisonous gases while running.
    DO NOT operate in an enclosed area.

•   Gasoline engine has hot and moving parts that can cause injury. 
    Use care when working with or near the gasoline engine and its parts.

•   Shut off engine when not in use, even for short periods of time, 
    to avoid damage to equipment or property.

65097

WARNING/CAUTION LABELS

Please become familiar with the Warning and Caution 
labels on the spreader.

NOTE: If labels are missing or cannot be read, see 
your sales outlet.

Summary of Contents for PRO-CASTER

























Reviews: