background image

Lit. No. 95902/95903, Rev. 01 

June 15, 2008

PREFACE

This manual has been prepared to acquaint you with 
the safety information, operation and maintenance of 
your new hopper spreader. Please read this manual 
carefully and follow all recommendations. This will 
help ensure pro

fi

 table and trouble-free operation of 

your hopper spreader. Keep this manual accessible. It 
is a handy reference in case minor service is required.

OWNER'S INFORMATION

Owner's Name:  ______________________________________________________________________

Date Purchased: _____________________________________________________________________  

Outlet Name: ______________________________________________  

Phone: __________________

Outlet Address: _______________________________________________________________________

Vehicle Model: _______________________________________________  

Year:  ________________

Spreader Type (Model): ________________________________________  Serial #: ________________

Length: ________________________  Weight 

__________________   lb/kg: 

 

__________________

When service is necessary, bring your hopper 
spreader to your local outlet. They know your spreader 
best and are interested in your complete satisfaction.

NOTE: This spreader is designed to spread snow 
and ice control materials only. Do not use it 
for purposes other than those speci

fi

 ed in this 

manual.

Summary of Contents for PRO-CASTER

























Reviews: