background image

3

1

 SAFETY AND WARNINGS

!

 WARNING!

Electric Shock Hazard

Read and follow the safety and warnings outlined in this installation 

guide before operating this appliance.

Failure to do so can result in death, electric shock, fire or injury 

to persons.

!

 WARNING!

Cut Hazard

Take care – panel edges are sharp. Failure to use caution could result 

in injury or cuts.

!

 WARNING!

This appliance is top-heavy and must be secured to prevent the 

possibility of tipping forward.
To ensure that the appliance is stable under all loading conditions, 

the anti-tip bracket and fittings supplied must be installed according 

to the following installation instructions by a professional installer.

IMPORTANT!

SAVE THESE INSTRUCTIONS

The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, 

go to our website fisherpaykel.com or contact your local Fisher & Paykel dealer.

IMPORTANT!

The water connection to your Ice & water refrigerator must be installed by an 

authorised plumber or Fisher & Paykel trained and supported service technician 

and comply with all state and local laws.

Installation and use MUST comply with all state and local plumbing codes. Check with 

your local public works department for plumbing codes. You must follow their 

guidelines as you install the water filtration system.

To avoid serious illness or death, only connect your water filter to safe drinking water.

The water filter cartridge needs to be changed when the replacement indicator icon 

illuminates. This will happen every 6 months.

If the water filtration system has been allowed to freeze, replace filter cartridge. 

Failure to replace the disposable filter at recommended intervals may lead to 

reduced filter performance and failure of the filter, causing property damage from 

water leakage or flooding.

In cases of excessively reduced filter life — we recommend that you consult a local 

plumber or your water supplier for advice on suitable filtration requirements for the 

water supplied to your home.

Filter replacement is the consumer’s responsibility and will not be covered by the 

warranty except in the case of faulty parts or materials within the filter cartridge.

If the water has not created ice for some time or ice has an unpleasant taste or odour 

dispose of ice and refer to the flushing instructions detailed in the installation section 

of this user guide/installation guide. If unpleasant taste or odor persists, you may 

wish to fit a new filter cartridge. 

Use new tubing supplied with the refrigerator. DO NOT reuse old tubing from old 

water and ice connections.

Your water filtration system can withstand up to 827kPa of water pressure. Ensure the 

supplied pressure reducing valve is installed before installing the water filtration 

system. DO NOT install if water pressure exceeds 827kPa.

To reduce the risk associated with property damage due to water leakage or flooding:

DO NOT install systems in areas where ambient temperatures may go above 38°C or 

drop below 0.6°C.

DO NOT install on hot water supply lines. The maximum operating water temperature 

of this filter system is 38°C.

DO NOT install where water hammer conditions may occur. If water hammer 

conditions exist, you must install a water hammer arrester.

WARNING!

To reduce the risk associated with choking:

DO NOT allow children under 3 years of age to have access to small parts during the 

installation of the water filter.

Summary of Contents for RS90A





























Reviews: