background image

7

WALL MOUNT

BACKGUARD

part no:

BGRU-3048

WALL MOUNT

BACKGUARD

part no:

BGRU2-1548

WALL MOUNT

BACKGUARD

part no:

BGRU-3048

WALL MOUNT

BACKGUARD

part no:

BGRU2-1548

WALL MOUNT

BACKGUARD

part no:

BGRU-3048

WALL MOUNT

BACKGUARD

part no:

BGRU2-1548

PRODUCT DIMENSIONS

36" MODELS

IN

MM

Overall height of range  
(from floor to cook surface, excl. pan supports and vent trim)

min 35 3/4 

max 36 3/4

min 908  

max 933

Overall width of range

35 7/8

911

Overall depth of range (excl. handle and dials)

29 1/8

740

Depth of chassis

25 3/8

644

Depth from rear of chassis to front of control panel

27 11/16

703

Height from top of cook surface to top of pan supports

1 9/16

40

Height from top of cook surface to top of 

 

z

vent trim (as illustrated)

 

z

angled vent trim (if fitted)

1 3/4
3 1/2

45

90

Height from top of cook surface to bottom of chassis

35 1/4

895

Adjustable feet height

min 1/2 

max 1 1/2

min 13 

max 38

Depth of open door to front control panel

19 1/8

486

PRODUCT DIMENSIONS – 36" MODELS

PLAN

PROFILE

FRONT

I

A

G

C

B

J

D

E

F

H

C

Summary of Contents for RDV3-304























Reviews: