manualshive.com logo in svg

Fisher & Paykel CLEANSMART WL8O60P, Installation Manual

Share
Download
Fisher & Paykel CLEANSMART WL8O60P Installation Manual Download Page 34

34

CHANGING PRE-SET OPTIONS

If you always use 

COLD

 or 

CONTROLLED COLD

 water, we recommend that a 

WARM

 or 

HOT

 

wash be used regularly, eg every 5th wash should be at least a warm one to maintain the 
cleanliness of your washer.

Out of balance recovery routine

When your washer is spinning it can sense if the wash load is out of balance. If an out of 
balance load is detected, the washer will stop and re-try spinning one more time. If it still 
senses an unbalanced load there are two options the washer can take.

Automatic recovery OFF (default setting)

Your washer will stop, beep, and show 

 in three phases on the display 

screen. You must redistribute the load more evenly yourself and touch 

 to resume the 

cycle. Use this option if you wish to conserve water.

2

Select 

COLD

 wash temperature by touching 

the 

WASH TEMP

 button (if not already 

selected).

3

The digital display shows the temperature 
adjustment possible. The default setting is 

, ie the temperature of the incoming 

water from the cold water supply.

4

Touch 

MORE

   until 

 is displayed. Your 

washer will now control the cold temperature 
to approximately 20°C. 
Each of the remaining settings equals an 
approximate 1°C temperature increase or 
decrease from this point.

Summary of Contents for CLEANSMART WL8O60P





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands