manualshive.com logo in svg

Fisher & Paykel CLEANSMART WL8O60P, Installation Manual

Share
Download
Fisher & Paykel CLEANSMART WL8O60P Installation Manual Download Page 11

INSTALLATION INSTRUCTIONS

11

Completing the installation

 

z

Turn on the water and check all hose connections for leaks. Make sure there are no kinks 
in the hoses. Check the hose connections for leaks again after 24 hours.

 

z

Uncoil power cord, remove and discard the plastic pin cover, and plug into wall socket.

 

z

Connect the appliance to an earthed outlet protected by a fuse of suitable capacity.

Installation test cycle

Your washer must be correctly installed before use. Check the installation and operation of 
the washer using the following procedure:

If there are any problems, you must address these before proceeding with normal use. The 

washer will automatically turn off at the end of the cycle if there are no problems.

1

Touch 

 to activate your washer.

3

Touch 

 to start the installation test cycle. 

The display will show

. 

 
The washer will beep to signal the end of 
the installation test cycle. Any faults will be 
displayed on the screen, refer ‘Fault codes’.

If you need further assistance, please contact 
a Fisher & Paykel trained and supported 
service technician or our Customer Care 
Centre. Refer to ‘Customer care’ section for 
contact details.

2

Touch   and 

OPTIONS

 together for 3 seconds.

+

Summary of Contents for CLEANSMART WL8O60P





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands