12
!1
FIT CLAMPING BRACKETS BASED ON THE
BENCHTOP THICKNESS
!2
SECURE TO BENCHTOP
!3
CONNECT TO GAS SUPPLY
!4
CHECK ALL CONNECTIONS FOR GAS LEAKS
GAS
ON
GAS
ON
PTFE
3⁄8
”
NPT
500 mm
50 mm
1
2
500 mm
25 mm
25 mm
500 mm
NG
NG
LPG
LPG
20-50 mm
½
“ BSP
½
“ BSP
x 4
1
1
2
2
16-20mm
20-30mm
Fibre washer
Floating nut
Elbow (½” BSP external thread)
LPG test point adaptor (if using LPG)
m
in
S
A
R
m
in
A
F
S
REAR CLAMPS
FRONT CLAMPS
40 mm
40 mm
30 mm
30 mm
30 mm
30 mm
Foam Tape
Adhesive side
Fibre washer
Floating nut
Elbow (½” BSP external thread)
NG Models
ALL Models
Make sure the connection point will be accessible with the cooktop installed.
To enable the gas supply to be readily shut off by the customer, make sure the connection
is fitted with an isolating valve close to the cooktop.
Make sure to fit the supplied
washer and regulator.
Adjust to obtain a
test point
pressure of 1 kPa
with the two
semi-rapid burners operating at
highest setting.
Ensure the hose is long enough to allow for removal of cooktop for servicing.
Make sure the connector is located as shown in step 3 CLEARANCE DIMENSIONS.
The hose assembly must be AS/NZS 1869 Class B or D certified, with an Rp ½” (ISO 7‐1) female thread connection.
The hose assembly must be as short as practicable and comply with relevant AS 5601/NZS 5261 requirements.
The hose must not be kinked, subjected to abrasion or permanently deformed.
The hose must not be near or in contact with any hot surfaces
(e.g. base of metal hotlplate, flue, or chassis of underbench oven etc.)
If connecting the gas with a flexible hose:
LPG Models
check all connections
Make sure to fit the supplied
washer and test point adaptor.
Make sure the
supply pressure
is regulated to 2.75 kPa
, with
the two semi-rapid burners
operating at highest setting.
Washer
Washer
yellow tip
lifting off
good flame
Arrow
x 4
x 4
30-40mm
40mm+
GAS
ON
GAS
ON
PTFE
3⁄8
”
NPT
500 mm
50 mm
1
2
500 mm
25 mm
25 mm
500 mm
NG
NG
LPG
LPG
20-50 mm
½
“ BSP
½
“ BSP
x 4
1
1
2
2
16-20mm
20-30mm
Fibre washer
Floating nut
Elbow (½” BSP external thread)
LPG test point adaptor (if using LPG)
m
in
S
A
R
m
in
A
F
S
REAR CLAMPS
FRONT CLAMPS
40 mm
40 mm
30 mm
30 mm
30 mm
30 mm
Foam Tape
Adhesive side
Fibre washer
Floating nut
Elbow (½” BSP external thread)
NG Models
ALL Models
Make sure the connection point will be accessible with the cooktop installed.
To enable the gas supply to be readily shut off by the customer, make sure the connection
is fitted with an isolating valve close to the cooktop.
Make sure to fit the supplied
washer and regulator.
Adjust to obtain a
test point
pressure of 1 kPa
with the two
semi-rapid burners operating at
highest setting.
Ensure the hose is long enough to allow for removal of cooktop for servicing.
Make sure the connector is located as shown in step 3 CLEARANCE DIMENSIONS.
The hose assembly must be AS/NZS 1869 Class B or D certified, with an Rp ½” (ISO 7‐1) female thread connection.
The hose assembly must be as short as practicable and comply with relevant AS 5601/NZS 5261 requirements.
The hose must not be kinked, subjected to abrasion or permanently deformed.
The hose must not be near or in contact with any hot surfaces
(e.g. base of metal hotlplate, flue, or chassis of underbench oven etc.)
If connecting the gas with a flexible hose:
LPG Models
check all connections
Make sure to fit the supplied
washer and test point adaptor.
Make sure the
supply pressure
is regulated to 2.75 kPa
, with
the two semi-rapid burners
operating at highest setting.
Washer
Washer
yellow tip
lifting off
good flame
Arrow
x 4
x 4
30-40mm
40mm+
view from below
GAS
ON
GAS
ON
PTFE
3⁄8
”
NPT
500 mm
50 mm
1
2
500 mm
25 mm
25 mm
500 mm
NG
NG
LPG
LPG
20-50 mm
½
“ BSP
½
“ BSP
x 4
1
1
2
2
16-20mm
20-30mm
Fibre washer
Floating nut
Elbow (½” BSP external thread)
LPG test point adaptor (if using LPG)
m
in
S
A
R
m
in
A
F
S
REAR CLAMPS
FRONT CLAMPS
40 mm
40 mm
30 mm
30 mm
30 mm
30 mm
Foam Tape
Adhesive side
Fibre washer
Floating nut
Elbow (½” BSP external thread)
NG Models
ALL Models
Make sure the connection point will be accessible with the cooktop installed.
To enable the gas supply to be readily shut off by the customer, make sure the connection
is fitted with an isolating valve close to the cooktop.
Make sure to fit the supplied
washer and regulator.
Adjust to obtain a
test point
pressure of 1 kPa
with the two
semi-rapid burners operating at
highest setting.
Ensure the hose is long enough to allow for removal of cooktop for servicing.
Make sure the connector is located as shown in step 3 CLEARANCE DIMENSIONS.
The hose assembly must be AS/NZS 1869 Class B or D certified, with an Rp ½” (ISO 7‐1) female thread connection.
The hose assembly must be as short as practicable and comply with relevant AS 5601/NZS 5261 requirements.
The hose must not be kinked, subjected to abrasion or permanently deformed.
The hose must not be near or in contact with any hot surfaces
(e.g. base of metal hotlplate, flue, or chassis of underbench oven etc.)
If connecting the gas with a flexible hose:
LPG Models
check all connections
Make sure to fit the supplied
washer and test point adaptor.
Make sure the
supply pressure
is regulated to 2.75 kPa
, with
the two semi-rapid burners
operating at highest setting.
Washer
Washer
yellow tip
lifting off
good flame
Arrow
x 4
x 4
30-40mm
40mm+
Repeat on all the other sides
GAS
ON
GAS
ON
PTFE
3⁄8
”
NPT
500 mm
50 mm
1
2
500 mm
25 mm
25 mm
500 mm
NG
NG
LPG
LPG
20-50 mm
½
“ BSP
½
“ BSP
x 4
1
1
2
2
16-20mm
20-30mm
Fibre washer
Floating nut
Elbow (½” BSP external thread)
LPG test point adaptor (if using LPG)
m
in
S
A
R
m
in
A
F
S
REAR CLAMPS
FRONT CLAMPS
40 mm
40 mm
30 mm
30 mm
30 mm
30 mm
Foam Tape
Adhesive side
Fibre washer
Floating nut
Elbow (½” BSP external thread)
NG Models
ALL Models
Make sure the connection point will be accessible with the cooktop installed.
To enable the gas supply to be readily shut off by the customer, make sure the connection
is fitted with an isolating valve close to the cooktop.
Make sure to fit the supplied
washer and regulator.
Adjust to obtain a
test point
pressure of 1 kPa
with the two
semi-rapid burners operating at
highest setting.
Ensure the hose is long enough to allow for removal of cooktop for servicing.
Make sure the connector is located as shown in step 3 CLEARANCE DIMENSIONS.
The hose assembly must be AS/NZS 1869 Class B or D certified, with an Rp ½” (ISO 7‐1) female thread connection.
The hose assembly must be as short as practicable and comply with relevant AS 5601/NZS 5261 requirements.
The hose must not be kinked, subjected to abrasion or permanently deformed.
The hose must not be near or in contact with any hot surfaces
(e.g. base of metal hotlplate, flue, or chassis of underbench oven etc.)
If connecting the gas with a flexible hose:
LPG Models
check all connections
Make sure to fit the supplied
washer and test point adaptor.
Make sure the
supply pressure
is regulated to 2.75 kPa
, with
the two semi-rapid burners
operating at highest setting.
Washer
Washer
yellow tip
lifting off
good flame
Arrow
x 4
x 4
30-40mm
40mm+
GAS
ON
GAS
ON
1
2
Fibre washer
Floating nut
Elbow (½” BSP external thread)
Foam Tape
Adhesive side
20 mm
50 mm
+50 mm
NG Models
ALL Models
Make sure the connection point will be accessible with the cooktop installed.
To enable the gas supply to be readily shut off by the customer, make sure the connection
is fitted with an isolating valve close to the cooktop.
Make sure to fit the supplied
regulator.
Adjust to obtain a
test point
pressure of 1 kPa
with all
burners operating at
highest setting.
Ensure the hose is long enough to allow for removal of cooktop for servicing.
Make sure the connector is located as shown in step 5 CLEARANCE DIMENSIONS.
The hose assembly must be AS/NZS 1869 Class B or D certified, with an Rp ½” (ISO 7‐1) female thread connection.
The hose assembly must be no longer than 1.2 m in length with minimum internal
diameter of 10 mm and comply with relevant AS 5601/NZS 5261 requirements.
The hose must not be kinked, subjected to abrasion or permanently deformed.
The hose must not be near or in contact with any hot surfaces
(e.g. base of metal hotlplate, flue, or chassis of underbench oven etc.)
If connecting the gas with a flexible hose:
LPG Models
recessed to 50 mm
check all connections
Make sure to fit the supplied
test point adaptor.
Make sure the
supply pressure
is regulated to 2.75 kPa
, with all
burners operating at highest
setting.
To check that the ignition system operates correctly, light each burner by itself, then all burners in combination.
Check for a well‐defined blue flame without any yellow tipping.
If any abnormality is evident, check that the components of the burner assembly are located properly
If proper operation cannot be obtained, contact your nearest F&P Authorised Service Centre.
The cooktop must not be used by the customer until proper operation has been achieved.
yellow tip
lifting off
good flame
Arrow
TG
ALL Models
Make sure the connection point will be accessible with the cooktop installed.
To enable the gas supply to be readily shut off by the customer, make sure the connection
is fitted with an isolating valve close to the cooktop.
Adjust to obtain a supply pressure of
1.5 kPa (Hong Kong) or 0.8 kPa (Singapore)
with all the burners operating at the
highest setting.
Ensure the hose is long enough to allow for removal of cooktop for servicing.
Make sure the connector is located as shown in step 5 CLEARANCE DIMENSIONS.
The hose assembly must be certified, with an Rp ½” (ISO 7‐1) female thread connection.
The hose assembly must be as short as practicable and comply with relevant local code and regulation requirements.
The hose must not be kinked, subjected to abrasion or permanently deformed.
The hose must not be near or in contact with any hot surfaces
(e.g. base of metal hotlplate, flue, or chassis of underbench oven etc.)
If connecting the gas with a flexible hose:
LPG
Make sure the
supply pressure
is regulated to 2.90 kPa
, with
all the burners operating at
highest setting.