11
7
DISCARD PACKAGING
9
FIT THE ELBOW AND WASHER
8
REMOVE THE TWO TRANSIT SCREWS
!0
LOWER GENTLY INTO THE CUTOUT
Nipple (½” NPT thread)
Foam Tape
Adhesive side
Ensure edge of tape
lines up with outer
edge of cooktop
Recycle responsibly
Model may vary from illustrations shown
GAS
ON
GAS
ON
PTFE
3⁄8
”
NPT
500 mm
50 mm
1
2
500 mm
25 mm
25 mm
500 mm
NG
NG
LPG
LPG
20-50 mm
½
“ BSP
½
“ BSP
x 4
1
1
2
2
16-20mm
20-30mm
Fibre washer
Floating nut
Elbow (½” BSP external thread)
LPG test point adaptor (if using LPG)
m
in
S
A
R
m
in
A
F
S
REAR CLAMPS
FRONT CLAMPS
40 mm
40 mm
30 mm
30 mm
30 mm
30 mm
Foam Tape
Adhesive side
Fibre washer
Floating nut
Elbow (½” BSP external thread)
NG Models
ALL Models
Make sure the connection point will be accessible with the cooktop installed.
To enable the gas supply to be readily shut off by the customer, make sure the connection
is fitted with an isolating valve close to the cooktop.
Make sure to fit the supplied
washer and regulator.
Adjust to obtain a
test point
pressure of 1 kPa
with the two
semi-rapid burners operating at
highest setting.
Ensure the hose is long enough to allow for removal of cooktop for servicing.
Make sure the connector is located as shown in step 3 CLEARANCE DIMENSIONS.
The hose assembly must be AS/NZS 1869 Class B or D certified, with an Rp ½” (ISO 7‐1) female thread connection.
The hose assembly must be as short as practicable and comply with relevant AS 5601/NZS 5261 requirements.
The hose must not be kinked, subjected to abrasion or permanently deformed.
The hose must not be near or in contact with any hot surfaces
(e.g. base of metal hotlplate, flue, or chassis of underbench oven etc.)
If connecting the gas with a flexible hose:
LPG Models
check all connections
Make sure to fit the supplied
washer and test point adaptor.
Make sure the
supply pressure
is regulated to 2.75 kPa
, with
the two semi-rapid burners
operating at highest setting.
Washer
Washer
yellow tip
lifting off
good flame
Arrow
x 4
x 4
30-40mm
40mm+
GAS
ON
GAS
ON
PTFE
3⁄8
”
NPT
500 mm
50 mm
1
2
500 mm
25 mm
25 mm
500 mm
NG
NG
LPG
LPG
20-50 mm
½
“ BSP
½
“ BSP
x 4
1
1
2
2
16-20mm
20-30mm
Fibre washer
Floating nut
Elbow (½” BSP external thread)
LPG test point adaptor (if using LPG)
m
in
S
A
R
m
in
A
F
S
REAR CLAMPS
FRONT CLAMPS
40 mm
40 mm
30 mm
30 mm
30 mm
30 mm
Foam Tape
Adhesive side
Fibre washer
Floating nut
Elbow (½” BSP external thread)
NG Models
ALL Models
Make sure the connection point will be accessible with the cooktop installed.
To enable the gas supply to be readily shut off by the customer, make sure the connection
is fitted with an isolating valve close to the cooktop.
Make sure to fit the supplied
washer and regulator.
Adjust to obtain a
test point
pressure of 1 kPa
with the two
semi-rapid burners operating at
highest setting.
Ensure the hose is long enough to allow for removal of cooktop for servicing.
Make sure the connector is located as shown in step 3 CLEARANCE DIMENSIONS.
The hose assembly must be AS/NZS 1869 Class B or D certified, with an Rp ½” (ISO 7‐1) female thread connection.
The hose assembly must be as short as practicable and comply with relevant AS 5601/NZS 5261 requirements.
The hose must not be kinked, subjected to abrasion or permanently deformed.
The hose must not be near or in contact with any hot surfaces
(e.g. base of metal hotlplate, flue, or chassis of underbench oven etc.)
If connecting the gas with a flexible hose:
LPG Models
check all connections
Make sure to fit the supplied
washer and test point adaptor.
Make sure the
supply pressure
is regulated to 2.75 kPa
, with
the two semi-rapid burners
operating at highest setting.
Washer
Washer
yellow tip
lifting off
good flame
Arrow
x 4
x 4
30-40mm
40mm+
Repeat on the other side
GAS
ON
GAS
ON
PTFE
3⁄8
”
NPT
500 mm
50 mm
1
2
500 mm
25 mm
25 mm
500 mm
NG
NG
LPG
LPG
20-50 mm
½
“ BSP
½
“ BSP
x 4
1
1
2
2
16-20mm
20-30mm
Fibre washer
Floating nut
Elbow (½” BSP external thread)
LPG test point adaptor (if using LPG)
m
in
S
A
R
m
in
A
F
S
REAR CLAMPS
FRONT CLAMPS
40 mm
40 mm
30 mm
30 mm
30 mm
30 mm
Foam Tape
Adhesive side
Fibre washer
Floating nut
Elbow (½” BSP external thread)
NG Models
ALL Models
Make sure the connection point will be accessible with the cooktop installed.
To enable the gas supply to be readily shut off by the customer, make sure the connection
is fitted with an isolating valve close to the cooktop.
Make sure to fit the supplied
washer and regulator.
Adjust to obtain a
test point
pressure of 1 kPa
with the two
semi-rapid burners operating at
highest setting.
Ensure the hose is long enough to allow for removal of cooktop for servicing.
Make sure the connector is located as shown in step 3 CLEARANCE DIMENSIONS.
The hose assembly must be AS/NZS 1869 Class B or D certified, with an Rp ½” (ISO 7‐1) female thread connection.
The hose assembly must be as short as practicable and comply with relevant AS 5601/NZS 5261 requirements.
The hose must not be kinked, subjected to abrasion or permanently deformed.
The hose must not be near or in contact with any hot surfaces
(e.g. base of metal hotlplate, flue, or chassis of underbench oven etc.)
If connecting the gas with a flexible hose:
LPG Models
check all connections
Make sure to fit the supplied
washer and test point adaptor.
Make sure the
supply pressure
is regulated to 2.75 kPa
, with
the two semi-rapid burners
operating at highest setting.
Washer
Washer
yellow tip
lifting off
good flame
Arrow
x 4
x 4
30-40mm
40mm+
Floating nut
Elbow (1/2” BSP thread) & Washer
HONG KONG
SINGAPORE
Floating nut
Fibre washer
Elbow (1/2” BSP external