background image

10

 

®

 

 

  

 

 

 

11.2  In case of air tube wear or damage: 

 

if air tube or mounting ring has to be replaced - order a replacement air tube (with mounting ring) of length 
“L” – prices on request only, 

 

if  just  the  end  of  air  tube  is  eroded  -  cut  200  mm  of  the  tube  tip,  order  and  weld  spare  part  
P/N 

SP-48-END

 - replacement air tube end, length 200 mm, SS310/330. 

List of pilot spare parts Part Numbers is in Table 2. 

11.3 

The  warranty  (see  page  16)  covers  delivered  devices  and  materials  under  conditions  of  proper 
installation,  start-up,  operation  and  maintenance,  it  means  the  use  in  accordance  with  applicable 
instructions and manuals.  

This  is  particularly  applicable  to  overheated  parts  i.e.  working  above  their  maximum  operating 
temperature defined in Instruction Manual.

 

11.4  The defective device or part will be replaced or repaired at manufacturer’s option. 

The warranty applies to and may be executed only on a failed device send to the manufacturer warehouse for 
examination or warranty repair.  

11.5  The manufacturer does not accept liability for damage to persons or property resulting from: 

 

mechanical damages, 

 

improper installation, operation, maintenance of igniter contrary to the instructions in the user manual, 

 

unauthorized igniter modifications or repairs made by unauthorized personnel, 

 

use of components or spare parts other than original. 

11.6  During the guarantee period any repairs must be carried out by the manufacturer service department, or the user, 

upon the service's notification and consent. 

11.7  Replacement of the consumables

 can be user-performed only after expiration of the guarantee.

 

 

FIGURE 5. 

Loose Spare Parts set for SP-32 and SP-48 pilots

 

Loose Spare Parts set includes: 

1 - rod gland ½” NPT (for 

SP-32 

and 

SP-48

) – 1 pc 

2 -  gasket OD 25x5 (for 

SP-32

) – 1 pc  

3 -  O ring 46x3 (for 

SP-48

) – 1 pc  

4 -  thumb screw M4 with snap ring 

(for 

SP-32-ND

 and 

SP-48-ND

)  – 1 pc 

 
 
 

 
 
 

12.  STORAGE 

SP-48

 gas pilot should be stored in a clean, dry environment and in its original packaging if possible. 

In case of long length pilots, always keep them in a horizontal position by supporting both ends and in the middle. It 
should also be protected from contamination using caps on gas and air inlet and pilot outlet and covered with foil. 
Storage over 30 days: relative humidity of no more than 85%, temperature below 50°C. 

 

 

NOTICE

:

   

THE  MANUFACTURER  RESERVES  THE  RIGHT  TO  CARRY  OUT 

MODIFICATIONS TO THE PRODUCT DESCRIBED  IN THIS INSTRUCTION MANUAL 
AT ANY TIME AND WITHOUT ANY ADVANCE NOTICE. 

.

 

 

Summary of Contents for SureFire II SP-48-NG-FD

















Reviews: