Fireye FlameWorx MBFR-100D Manual Download Page 9

Page: 9 / 12



WIRING DIAGRAM

The wiring base for the DIN rail mount flame modules (60-2537) provides 16 terminals for wiring
the FlameWorx modules.

FIGURE 4.

Internal/External Wiring Connections

FIGURE 5.

Scanner wiring diagram for MBHPS-100D and MBLPS-100D power supply and MBUV-100D,
MBUVS-100D, MBFR-100D, and MBIR-100D FlameWorx modules and their associated scanners.

Power for flame rod and UV scanner(s) (from MBHPS-100D, -200D power supply)

Power for flame rod and UV scanner (s) (from MBHPS-100D, -200D power supply)

Scanner input (flame signal) - Flame Switch (Channel #1)

Scanner input (flame signal)- Flame Switch (Channel #2)

Flame relay normally open (NO) contact - Flame Switch (Channel #1)

Flame relay common - Flame Switch (Channel #1)

Flame relay normally closed (NC) contact or 4-20 mA output
- Flame Switch (Channel #1)

Flame relay normally closed (NC) contact or 4-20 mA output
- Flame Switch (Channel #2)

Flame relay common - Flame Switch (Channel #2)

Flame relay normally open (NO) contact - Flame Switch (Channel #2)

Input power (24 VAC / 24 VDC)

Input power common

LonWorks Communications (Data A)

LonWorks Communications (Data B)

4-20MA

JP4

JP5

INTERNAL CONNECTIONS

EXTERNAL CONNECTIONS

Jumpers JP4 and JP5 are
shipped from the factory
in positions 2-3, providing the flame
relay normally closed (NC)
contact.

USE TERMINAL 14 (INPUT POWER COMMON) AS THE COMMON RETURN FOR
EITHER /BOTH 4-20 mA OUTPUT SIGNALS. JUMPER(S) JP4/JP5 ARE SET IN POSITION 1-2.

69ND1
45CM1

48PT2

UV1A

1
2
3
4
5
6

13
14

45UV5-1008
45UV5-1009

1
2
3
4
5
6

13
14

1
2
3
4
5
6

13
14

1
2
3
4
5
6

13
14

45UV5-1008
45UV5-1009

1
2
4
5
7
8

MBHPS-100D

MBUVS-100D

MBFR-100D

MBIR-100D

CONNECT TO TERMINALS

10 AND 11 ON MBHPS/MBLPS

POWER SUPPLY OR SUITABLE

120VAC POWER SOURCE

CHANNEL 2

BLACK LEADS

CHANNEL 2

CHANNEL 1

ALL DIN RAIL FLAMEWORX
MODULES USE THE 60-2537
WIRING BASE.

NOTE: TERMINALS 1 AND 2 OF THE
MBIR-100D FLAMEWORX MODULE
DO NOT HAVE TO BE POWERED BY
MBHPS-100D POWER SUPPLY.

MBLPS-100D AND MBHPS-100D
USE THE 60-2538 WIRING BASE.

MBUV-100D

CHANNEL 1

REPLACEMENT FUSE
FOR MBPS-100D
(P/N 23-184).

RED LEADS

11
12

3
4
5
6

10
11
12

EARTH

MBLPS-100D

(120 VAC)

PHOTOCELL OR
FLAME ROD ONLY

MBFR ONLY

Summary of Contents for FlameWorx MBFR-100D













Search results

Summary of Contents for FlameWorx MBFR-100D

Reviews:

Related manuals for FlameWorx MBFR-100D

Brands by name

Popular brands

Fireye FlameWorx MBFR-100D, Manual

Search results

Summary of Contents for FlameWorx MBFR-100D

Reviews:

Related manuals for FlameWorx MBFR-100D

Brands by name

Popular brands