manualshive.com logo in svg

Firetide HotPort 3203, Hardware Installation Manual, Page: 28 / 37

Share
Download
Firetide HotPort 3203 Hardware Installation Manual Download Page 28

HotPort 3203 Outdoor Wireless Mesh Node 

 

27 

 

Connecting the Power 

There are two ways to provide power to the HotPort 3203: 

•

  By connecting the provided power supply to an AC power outlet and then to the HotPort 

3203. This option allows you to provide power to up to two peripheral devices connected 

to the HotPort 3203. 

•

  By connecting Power Sourcing Equipment to the HotPort 3203 (Power over Ethernet 

option).  

Connecting AC Power 

Use the supplied country- or region specific power cord, power transition cable, and power supply 

to provide power to the HotPort 3203 enclosure from an AC outlet. 

 

1.  Connect the female plug on the country- or region specific power cord to the power supply. 

2.  Connect the four-pin plug on the power transition cable to the power supply. 

3.  Run the power transition cable from the AC outlet location to the HotPort 3203 enclosure.  

4.  Remove the protective cap from the DC input connector on the HotPort 3203 enclosure and 

attach the six-pin connector on the power transition cable to the DC input connector on the 

HotPort. Twist the connector until it snaps into place to ensure a watertight seal. 

5.  Plug the free end of the country- or region specific power cord into an AC outlet. The 

indicators (LEDs) on the enclosure should light as follows:  after system startup, the Status 

light and the green Power light should light. 

 

 

HotPort 3203 Rear/Bottom Panel 

 

Ethernet Port 1  Ethernet Port 2 

DC Input Connector 

Status LEDs 

Summary of Contents for HotPort 3203






































Reviews:

No comments