background image

Hardware Installation Guide 

 

36 

Appendix C - Specifications 

 

Model 

HotPort 3203

 

 

Protocol 

Firetide Mesh Routing Protocol (FMRP) 

 

Encryption 

  40/64 bit, 104/128 bit WEP keys 

  128 bit, 256 bit AES keys 

 

Wireless interface 

2.4 GHz spectrum 

  2.400–2.497 GHz  

(actual channels available for use are 

subject to country-specific regulatory 

approvals) 

  TX Power: Up to 4 W EIRP depending on 

country of operation and antenna 

configuration 

 

5 GHz spectrum 

 

  5.250 – 5.350 GHz 

 

5.750 – 5.825 GHz 

(actual channels available for use are 

subject to country-specific regulatory

 

approvals) 

  TX Power: Up to 1 W EIRP depending on 

country of operation and antenna 

configuration 

Dynamic Frequency Selection (DFS) 
Transmit Power Control (TPC) 

 

Network ports 

  Dual 10/100 Mbps Ethernet ports with 

circular, watertight IP67-rated 

connectors 

  IEEE 802.3, 802.3u compliant 

  CSMA/CD 10/100 autosense 

 

Antennas 

  Two detachable, 6 dBi omni-directional, 

vertical polarization, dual spectrum antennas

 

(included for network staging only)  

  Single detachable 8 dBi omni-directional, 

vertical polarization antenna (order 

separately) 

Note: antennas are spectrum specific 

  Spectrum: 2.4 GHz and 5 GHz 

 

Connectors: TNC r

everse polarity 

  Length: 16.5 in. (42 cm) 

  Range: up to 2600 ft (800 m) depending on 

spectrum and environmental attenuation 

  Gain: up to 8 dBi 

 

Enclosure  

  Cast aluminum NEMA-4X/IP67 enclosure 

  Two antenna connectors (TNC reverse 

polarity) 

  One power connector 

 Two 

circular, watertight IP67-rated

 

Ethernet 

data connectors 

  System indicator LEDs (power, status, fault) 

  Physical security via lockable mounting 

bracket 

  Weight: 4.85 lbs (2.2 Kg) with sun shield 

  Dimensions: 9.812” x 7.812” x 2.687” (25 cm 

x 19.8 cm x 6.82 cm) 

 

Power 

  Input voltage: 24 VDC 

  Indoor-rated power supply (transformer): 90-

240 VAC, 50/60 Hz 

  Power consumption: 25 W nominal 

  802.3af compliant PoE (PD and PSE) 

  Power transition cable: 32.8 ft (10 m) 

 

Regulatory Agency Certifications 

Contact your Firetide dealer for product 

availability and certifications for your country 

 

Environmental specifications 

  Operating temperature: -40

o

 C to +55

 

C  

(-40

o

  

F to 131

o  

F) 

  Storage temperature: -40

o

 C to +80

o

 C  

(-40

o

  

F to 176

o  

F) 

  Humidity (non-condensing) 5% to 95% 

  Storage humidity (non-condensing): 10% to 

90% 

 

Mesh Management Software 

Includes HotView mesh management software 

 

Warranty 

One year limited warranty (see warranty card for 

details) 

 

Included Accessories 

  Lockable bracket for pole and wall mounting 

  Indoor-rated power supply 

 Sun 

shield 

  Weatherized Ethernet transition cable 

(

circular, watertight IP67-rated

 

connector

 

to 

RJ-45 connector) 

  Weatherized RJ-45 connector kit 

 

 

 

(The power lavel of the highest gain antenna 

is 11.194mW )

Single detachable 19 dBi panel antenna.

Summary of Contents for HotPort 3203






































Reviews: