background image

 

 

8. Limited Warranty 

FireFlex

®

 

Systems 

Inc. (known herein as "the 

Manufacturer") warrants to its customer that its products 
shall be free of defects in material or part(s) and 
workmanship for a period of twelve (12) months from the 
date of original delivery, under normal use and service by 
the Customer (and provided that the product has been 
properly installed and maintained). 

The obligation of the Manufacturer in case of a claim 
made by the Customer hereunder, shall be, at the 
Manufacturer's option, limited to repair or replace, free of 
charge for parts or his labor, any product or part, which in 
the opinion of the Manufacturer, shall be proven to be 
defective. The Manufacturer will NOT accept labor back-
charges incurred by the Customer to repair or replace 
said product or part. 

The present warranty shall be void should the product or 
part(s) be altered by anyone other than the Manufacturer. 
In case of a claim under the present warranty, the 
Customer must contact the Manufacturer's Customer 
Service Department as soon as he is aware of a claim 
and, subject to the authorization of the manufacturer, 
return the defective product or part(s), transportation 
prepaid, to the address listed below. 

This warranty constitutes the entire warranty given by the 
Manufacturer to the Customer with respect to the product.  
The present warranty is non-transferable and non-
assignable. The Manufacturer does not represent that the 
products will prevent any loss by fire or otherwise or that 
the product will in all cases provide the protection for 
which it has been installed or intended. 

The Customer acknowledges that the Manufacturer is not 
an insurer.  The manufacturer shall not be liable for any 
loss or damages of any nature whatsoever, including but 
not limited to incidental or special or consequential 
damages including but not limited to, property damages, 
personal injury, revenue loss or lost profits, 
inconveniences, transportation charges or other damages 
suffered by anyone. 

There are no other warranties, expressed or implied with 
regard to the products, other than those contained herein. 

Some jurisdictions may not allow limitations on how long 
an expressed warranty lasts, so the above limitations 
may not apply to you. Under no circumstances, shall the 
Manufacturer be liable for any loss of, or damage to 
property, direct or indirect, incidental or special or 
consequential damages, arising out of the use or inability 
to use the Manufacturer's products.  The Manufacturer 
shall not be liable for any personal injury which may arise 
in the course of or as a result of the use of the 
manufacturer's products. 

This warranty replaces all previous warranties and is the 
only warranty given by the Manufacturer with respect to 
its products.  This warranty shall not be modified, unless 
such modification is made in writing by an executive 
officer of the Manufacturer. 

In consideration of the warranty provisions contained 
herein, the Customer hereby waives the benefit of any 
statutory warranty or protection or remedy to which he 
may be entitled under the terms of any sales of goods act 
or similar legislation available to him in any jurisdiction in 
which the Customer carries on business. 

Defective part(s) must be returned to the address listed 
below within (30) days of receiving replacement parts(s).  
If defective part(s) is not returned before delay expires, 
an invoice will be issued for replacement part(s) and 
shipping.  On reception, an extended analysis will be 
performed on the said part(s).  If proven to be defective, 
no invoice will be issued.  If the part(s) is proven to be in 
working condition an invoice will be issued for 
replacement part(s) and shipping. 

 

Product Support 

1-866-347-3353 

Our Product Support Organization is dedicated to 
assisting you regarding our products, warranty and 
service procedures. 

The number above is a toll free number to Product 
Support. 

 

Manufactured by

  F

IRE

F

LEX

 Systems Inc.

 

1935, Lionel-Bertrand Blvd. 

Boisbriand, Quebec 

Canada J7N 

1N8 

Tel.: (450) 437-3473  

  Fax: (450) 437-1930 

Toll Free: (866) 347-3353 

Web site:  http://www.fireflex.com   

Email: 

[email protected]

 

 

Summary of Contents for N2 BLAST































Reviews: