background image

F

IRE

F

LEX

®

  N

2

 

B

LAST

®

 

Integrated Fire Protection System 

O

WNER

'

O

PERATION 

&

 

M

AINTENANCE 

M

ANUAL

 

FM-076B-0-6A 

Page 15 of 25

 

4.10  OPTIONAL SHUT-OFF VALVE AND SIGHT GLASS 

The shut-off valve & sight glass option is intended to be 
used for applications where testing of the system operation 
without filling the sprinkler piping network is desirable and 
where it is critical that all functions of the preaction system 
be tested under actual discharge conditions. 

Operation of the shut-off valve 

Inspection of the system can be implemented without filling 
the sprinkler piping system with water. 

1.  CLOSE the shut-off valve 

(D4)

2.  OPEN the main drain valve 

(D3)

3. Simulate 

the 

operation 

of the system to open the 

deluge valve 

(A1)

 (refer to chapter 

4.8.6 ANNUAL 

INSPECTION).  Verify that water flows through the 
sight glass assembly 

(D5)

4.  Once tests are completed, make sure the main drain 

valve 

(D3)

 is completely CLOSED.  Reset the system 

(refer to chapter 4.6 PLACING THE SYSTEM BACK IN 
SERVICE AFTER OPERATION). 

5.  FULLY OPEN the system shut-off valve 

(D4)

.  Reset 

the remote releasing control panel. 

Figure 4.7 - Shut-off valve option 

Main Drain

Valve (D3)

Deluge (A1) or

Flow Control (A2)

Valve

Supervised

Shut-off Valve (D4)

Sight Glass

Assembly (D5)

Riser Check

Valve  (D2)

Point flash light here

Supervised

Water Supply

Control Valve (D1)

FM-061H-0-75B

 

4.11  OPTIONAL SEMI-FLANGED INLET/OUTLET 

When required by the user, 

F

IRE

F

LEX

®

 

N

2

 Blast

®

 unit 

can be provided in a semi-flanged configuration. 

The semi flanged option provides flanged fittings only 
on the water inlet pipe (left side) and on the system 
riser outlet.  The drain manifold is provided with a 
threaded connection (left side).  The rest of the fittings 
are the same as usual with the main components being 
provided in the standard flanged / grooved 
configuration. 

Figure 4.8 - Semi-flange option 

Flanged fitting outside cabinet

(when provided)

Field connection

to Water Supply

(specify side)

Threaded end

Field Connection

to Open Drain

(specify side)

Flanged fitting outside cabinet
(when provided)

FM-061H-0-77B

 

 

Summary of Contents for N2 BLAST































Reviews: