finmon mi64 User Manual Download Page 27 | Manualshive

Page: 27 / 30

finmon mi64 User Manual Download Page 27

Troubleshooting

In this section we have given some advice for standard problems that you may
encounter. If you cannot find a solution here, please contact your installer or
monitoring company.

12.1 Fault Conditions

If a fault condition occurs your power indicator will turn red. You can view the
fault, and depending on the type can resolve it yourself or contact your
installer/monitoring company.

When

Your power indicator is flashing and you want to know
what the fault is.

How



Touch [ALT] then [7].



An illuminated zone indicator/s will indicate the
fault condition/s.



Refer to 12.1.1 to see what fault has occurred.

12.1.1

Fault Indicators and what to do

Zone
Status
Indicator

Fault Conditions

Suggested Action

1

Siren Tamper

Contact your installer.

2

Auxiliary 12V
Tamper

Contact your installer.

3

Box Tamper

Contact your installer.

4

AC Loss

Check that plug for the AC is in place
and turned on. If it is, and the fault is not
cleared- contact your installer.

5

Communication
Fail

Contact your installer.

6

Low Battery

Check that the plug for the mi64 is in
place and turned on.
If it is, and the fault is not cleared-
contact your installer.

7

Device Tamper

Contact your installer.

8

Device Loss

Contact your installer.

9

Network Trouble

Contact your installer.

27

Mi64 2017

«
...
25
26
27
28
29
...
»

Summary of Contents for mi64































Reviews:

No comments