FingerTec Face ID 5 Series User Manual Download Page 25 | Manualshive

Page: 25 / 52

background image

25

To configure the Wiegand output parameters:

Step 1:

Menu

>

Comm.

>

Wiegand Setup

>

Select Wiegand Out

>

OK.

Step 2:

Configure the Wiegand data settings

• SRB:

Prevent the lock from being opened due to device removal.

• Wiegand Format:

26-bits

• Wiegand Output bits:

Select one corresponding output digits in the Wiegand format.

• Failed ID:

System will directly regenerate a new card number or personnel ID for failed

IDs.

• Site Code:

can be set manually and is repeatable in a different device. Valid value

ranges from 0 to 256 by default.

• Pulse Width:

The changes of quantity of the electric charge with high-frequency ca-

pacitance within a specified time.

• ID Type:

Identifies the content of the data output by Wiegand (User ID and badge

number)

Ingress Online Activation

Ingress is a genuine software by FingerTec. Every FingerTec time attendance model
comes bundled with a unique license key. To start using the terminal with Ingress, you
must connect the terminal to Ingress and perform an online activation. Ingress reads
the serial number of your terminal and sends it for verification at the FingerTec server
via the Internet.

In case you do not have an Internet connection, you need to do offline activation.
Please send the serial number and model of your terminal to your local reseller or

[email protected]

to request for a product key

Installation and Setup of Ingress

Install Ingress in a PC that fulfils the software’s minimum requirements. Refer to

http://www.fingertec.com/customer/download/postsales/SUM-Ingress-E.pdf

for the Ingress user guide online. Setup Wizard will require you to do online activation
before any connection is established between Ingress and the terminal(s).

• •

«
...
23
24
25
26
27
...
»

Summary of Contents for Face ID 5 Series





















































Reviews:

No comments

Related manuals for Face ID 5 Series

Vodafone SGH-L810V

Brand: Samsung Pages: 93

Brand: Fanvil Pages: 16

Brand: Pacbrake Pages: 9

Brand: GÄN Pages: 24

Brand: Jabra Pages: 4

Brand: Valor Pages: 72

Brand: M-Audio Pages: 14

Brand: Waldbeck Pages: 7

Aerasgard KCO2-W

Brand: S+S Regeltechnik Pages: 16

Brand: BAFANG Pages: 9

Brand: Fantec Pages: 5

Brand: Obelink Pages: 2

Brand: Calix Pages: 5

Brand: Conrad Pages: 26

Brand: Kettler Pages: 4

Brand: hepco & becker Pages: 4

Radfire RAS Series

Brand: Puretec Pages: 8

Brand: WABCO Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands