background image

6

7. Assembly Instruction

 ATTENTION – 

A

To avoid risks of electrical shock, all installation and 

wiring operations must be carried out with the DC disconnect switch 

internal and external (if present, applying LOTO procedures on it) 

to OFF position and with the external AC disconnect switch to OFF 

position (applying LOTO procedures on it).

 ATTENTION – 

A

During installation, do not place the equipment with 

its front facing towards the ground.

  READ THE MANUAL  – 

E

The underlying procedure is related to the 

side-by-side installation of REACT2-BATT. Alternatively, is possible to 

install the REACT2-BATT separately and at greater distances using 

the “REACT2-XL-CABLE-KIT” cable kit (2 meter cables length).

• Position the REACT2-BATT bracket 

(20)

 so that it is perfectly level on the 

wall and use it as a drilling template. To aling the two brackets use the 

reference point and follow the steps as in the picture.

•  It is the installer’s responsibility to choose an appropriate type of screw 

anchors for the attachment points. The choice must be based on the type 

of support (wall, frame or other support), the type of anchors to be used, 

and their ability to support 4 times the inverter’s weight (4x50Kg=200Kg). 

Depending on the type of anchor chosen, drill the required 2 holes 

B

 to 

mount the bracket. 

• Install the REACT2-BATT bracket 

(20)

 to the support.

01

20

B

B

2 x  

Ø

 9 mm

STEP 1

STEP 2

•  Lift the REACT2-BATT up to the bracket and insert the heads of two 

anchor points (present on the back of the battery unit) into the slots   

on the bracket 

(20)

.

 LIFTING – 

U

Risk of injury due to the heavy weight of the equipment.

• Hang up the lower part of the REACT2-BATT to the wall using the two wall 

attachment point 

(26)

(holes diameter 11 mm).

• Remove the caps from the battery and inverter connectors (if present). 

- To remove the battery signal connectors 

(08)

 simply pull it. 

 

- To remove the battery power connectors 

(09)

 press the latch (highlighted 

in red) and pull it off.

DC SWITCH

COM.

GRID

+/ -

COMM.

[B]

POWER

[B]

COMM.

[A]

POWER

[A]

08

09

09

08

• Connect the two battery cables between inverter and battery unit 

(supplied inside the REACT2-UNO box).

• Give each cable a pull test to confirm the connection is secure.

Click 

Click 

Click 

COMM.

[B]

POWER

[B]

COMM.

[A]

POWER

[A]

Click 

COMM.

[B]

POWER

[B]

COMM.

[A]

POWER

[A]

Click 

Click 

To execute all external grounding connection, follow the procedure 

described below:

1. Make a jumper earth cable using the two cable lugs supplied (minimum 

cross-section not less than 4mm²). The cable must be long enough to 

connect the REACT2-UNO external protective earth 

(11)

 to the REACT2-

BATT external protective earth [A] 

(25)

.

2. From among the components supplied, find the M5 nut, M5 flat washer 

and M5 serrated lock washer.

Summary of Contents for REACT2-BATT









Reviews: