background image

3

3.  List of supplied components

Available components for REACT2-BATT

Qty

Bracket for REACT2-BATT wall 

mounting

1

Cable lug for earth cable

2

REACT2-BATT power 

connection cable

1

REACT2-BATT signal 

connection cable

1

 

M5 hex nuts , M5 flat washer 

and M5 serrated lock washer 

for protective earth cable 

installation

1+1+1

Technical documentation

1

4.  Safety precautions

Battery System provides a safe source of electrical energy when operated 

as intended and as designed.

Potentially hazardous circumstances such as excessive heat or electrolyte 

mist may occur under improper operating conditions, damage, misuse 

and/or abuse. The following safety precautions and the warning messages 

described in this Part must be observed. 

 ATTENTION – 

A

HIGH VOLTAGE – ELECTRIC SHOCK HAZARD. 

Do NOT open any cover of REACT2-BATT

4.1  Organic Solvent Electrolyte

Cell components of Battery System contain organic solvent-based 

electrolyte. Breach of individual cells may allow some electrolyte to be 

released from the cell. Direct contact with the liquid electrolyte can cause 

skin irritation. 

If contact with the liquid electrolyte occurs, follow the suggestions below to 

minimize the chance of injury: 

• Flush eyes immediately with cold running water for at least 15 minutes. 

• Rinse skin immediately with water for at least 15 minutes. 

• Remove clothing if soiled. 

• Seek immediate medical attention.

4.2  Electrolyte Vent Product

Organic solvent electrolyte vent products are flammable. To avoid of 

flammable products, the following guidelines must be observed:

•  Operate the Battery System under conditions only as specified

•  Keep sparks, flames and smoking materials away from the Battery

•  Do not incinerate, puncture or impact the Battery System.

•  Do not solder or weld to the Battery System.

 ATTENTION – 

A

HAZARD. The hazard warnings (set out below) are 

used to indicate risks or unsafe practices that CAN cause serious 

injury or death.

•  DO NOT dismantle or disassemble any parts.

•  DO NOT set light to or heat.

•  DO NOT use or leave near a naked flame, boiler or heated places 

(beyond the temperature range indicated in the technical data). 

•  DO NOT wet with fresh or salt water. 

•  DO NOT create damaging impacts or drop.

•  DO NOT use for other equipment. 

•  DO NOT touch directly if there is a leak of electrolyte material. 

•  DO NOT touch if it shows any breaks in the cover where any parts under 

voltage are visible.

•  DO NOT use should a fault or any anomaly (such as in smell, heat, 

colour, smoke, shape or noise) be found.

 WARNING – 

B

The warnings (set out below) are used to indicate risks 

or dangerous actions which COULD cause serious personal harm or 

damage to the product or property.

•  Do not use with other inverter models if not expressly indicated by 

FIMER. 

•  Do not use if is leaking of electrolyte material.

•  Do not use if anomalies are present. Should the battery unit have a bad 

smell, changes in colouring, deformation or other anomalous conditions 

during use (including charging and storage), do not use it.

 ATTENTION – 

A

CAUTION. The caution messages (set out below) 

are used to indicate risks or dangerous actions which could cause 

serious harm to people or damage to property.

•  Do not use or leave exposed to direct sunlight (or in a vehicle which is 

exposed to the sun). The REACT2-BATT could produce heat, smoke, 

breakages or flames. In addition, its performance might deteriorate and/

or it might have a shorter lifespan.

 ATTENTION – 

A

Final installation of the equipment must not hinder 

access to any externally located disconnection devices.

Summary of Contents for REACT2-BATT









Reviews: