background image

PAGE / 10  

Doc. P/N 06-905 

Rev. 1 / December 2018 

 

9.  With  the  leads  connected  and  the  appropriate  test  jumper  installed,  the  Analyzer  will  initiate  a  30-second 

countdown timer to ensure the internal series firing circuit on the EPC is charged and ready to fire. The Analyzer 
will display a countdown to indicate when the time delay has expired and the EPC is ready for testing. 

 

 

10.  Once the countdown timer reaches 0, the display will indicate the system is ready to be activated. 

 

 

11. 

WAIT!

 

DO NOT use the ACTIVATE button on the Analyzer to initiate the test. Instead, activate the series firing 

circuit by initiating an input signal at the EPC’s 4-20 mA detection inputs (P2-1 or P2-2).   

12.  The Analyzer will then display the reading obtained during the test, along with the PASS/REPLACE result.  

 

 

13.  Record the reading obtained for future reference, since subsequent tests will override current test data.  

14.  Reset the EPC and ensure it is in a normal “up” condition, with no trouble light on.  

15.  Proceed to Test 4. 

7.3.4.

 

  Test 4: Field Wiring Supervisory Current Test 

This Output Analyzer test verifies the supervisory current being supplied by the EPC to the field devices through 
series firing circuit field wiring. The Analyzer comes with jumpers and test leads used to perform this test. To get 
started:  

1.  Connect the alligator leads to the Analyzer and field box terminals, as shown in Figure 7.3.3-1.   

2.  Install the 75Ω Resistor on the Analyzer.   

3.  The supervisory current supplied by the series firing circuit (P3-2) will be displayed. The reading must be within 

two tenths of the value measured in Test 2.  

 

 

4.  Record the reading obtained for future reference, since subsequent tests will override current test data.  

5.  Return to the main menu and select the EPC tool again. 

6.  Disconnect the test connector from the field box terminals. 

7.  Power down the EPC. 

8.  Install  a  1-Ohm  Resistor  (P/N  E10-0174)  onto  the  field  box  terminals  where  the  GCA  leads  are  normally 

connected. 

9.  Ensure the EPC is in a normal “up” condition, with no trouble light on. 

10.  Repeat Tests 3 and 4 for each field box, measuring both the activation and supervisory current for each box. 

11.  End of testing. Place system back into normal operational state.     

 

   

 

Wait: Charging 
Countdown: 30 

System Ready 
Activate Now 

2.8 2.7 2.7 2.6 
REPLACE EPC 

5.97 5.7 5.5 5.2 
EPC Passes 

Supervisory 
Current: 5.9mA 

Summary of Contents for 10-2983























Reviews: