Fieldpiece HVAC Guide HG1 Field Manual Download Page 33

Page: 33 / 37

WWW.FIELDPIECE.COM WWW.FIELDPIECE.COM WWW.FIELDPIECE.COM WWW.FIELDPIECE.COM WWW.FIELDPIECE.COM WWW.FIELDPIECE.COM WWW.FIELDPIECE.COM WWW.FIELDPIECE.COM WWW.FIELDPIECE.COM WWW.FIELDPIECE.COM WWW.FIELDPIECE.COM

Air Conditioning Basics

The Evaporator, Condenser, Restrictor (Throttling

valve) and Compressor are the four basic components

of an air conditioner. Following one pound of refriger-

ant through the system shows the function of each com-

ponent.

Subcooled liquid refrigerant at high pressure enters

the restrictor and is throttled to saturated refrigerant at

a lower pressure. The restrictor can be of either a fixed

or TXV/EXV type. The fixed type must be charged to

a target superheat that varies with indoor and outdoor

conditions. The evaporator capacity varies with the in-

door heat load on a fixed restrictor. The TXV/EXV regu-

lates the size of the restriction to maintain a constant

superheat. This essentially adjusts the capacity of the

evaporator responding to the indoor heat load. TXV/

EXV systems must be charged to subcooling.

After the restrictor, refrigerant enters the evaporator

at a low temperature and pressure and boils (evaporates)

into a gas by absorbing heat from the indoor air. The re-

frigerant stays at the same temperature and pressure un-

til all the refrigerant evaporates into a gas. After the re-

frigerant becomes a gas, it will become superheated and

the temperature will change. The superheat measure-

ment is the best indication of refrigerant charge level in

a fixed restrictor system and a TXV/EXV system will

keep the superheat constant. There must be superheat

present to ensure liquid does not flood the compressor.

Superheat measurements are taken on the suction line

between the evaporator and compressor.

The compressor takes this low temperature, low

pressure, and slightly superheated refrigerant and com-

presses it into a much higher temperature and pressure.

The highly superheated gas enters the condenser

and rejects heat into the outside air. The refrigerant

condenses back into a liquid. Once all of the gas is con-

densed into a liquid then additional removal of heat

causes a temperature drop known as subcooling. TXV/

EXV systems are charged to subcooling since superheat

is controlled by the throttle valve. Subcooling measure-

ments are taken on the liquid line between the condens-

er and TXV/EXV (fig. 33). Then the subcooled liquid

enters the restrictor, and the cycle starts again.

Figure 33. The Refrigeration Diamond.

Summary of Contents for HVAC Guide HG1






































Search results

Summary of Contents for HVAC Guide HG1

Reviews:

Related manuals for HVAC Guide HG1

Brands by name

Popular brands

Fieldpiece HVAC Guide HG1, Field Manual

Search results

Summary of Contents for HVAC Guide HG1

Reviews:

Related manuals for HVAC Guide HG1

Brands by name

Popular brands