manualshive.com logo in svg

FIBARO FIBEFGBS-222, Manual, Page: 4 / 12

Share
Download
FIBARO FIBEFGBS-222 Manual Download Page 4

You can connect up to 2 analog sensors IN1/IN2 terminals.
 
1. Disconnect Power
2. Connect with the diagram below
 

 
3. Verify the correctness of connection.
4. Power the device.
5. Add the device to the Z-Wave network.
6. Change values of parameters:

Connected to IN1: change parameter 20 to 4

Connected to IN2: change parameter 21 to 4

Connection with binary sensor or button

 

You connect normally opened or normally binary sensors to IN1/IN2 terminals.

 
1. Disconnect Power
2. Connect with the diagram below
 

 
3. Verify the correctness of connection.
4. Power the device.
5. Add the device to the Z-Wave network.
6. Change values of parameters 
6.1 Binary sensor

Connected to IN1:

Normally close: change parameter 20 to 0

Normally open: change parameter 20 to 1

Connected to IN2:

Normally close: change parameter 21 to 0

Normally open: change parameter 21 to 1

6.2 Button

Connected to IN1:

Monostable: change parameter 20 to 2

Bistable: change parameter 20 to 3

Connected to IN2:

Monostable: change parameter 21 to 2

Bistable: change parameter 21 to 3

Summary of Contents for FIBEFGBS-222













Reviews:

No comments