manualshive.com logo in svg

FIBARO FIBEFGBS-222, Manual, Page: 10 / 12

Share
Download
FIBARO FIBEFGBS-222 Manual Download Page 10

This parameter defines minimal change (from the last reported) of internal temperature sensor value that results in sending new report. 

Size: 2 Byte, Default Value: 5

Setting

Description

0

reporting on change disabled

1 - 255

(0.1-25.5C)

Parameter 66: Internal temperature sensor - periodical reports

This parameter defines reporting period of internal temperature sensor value. Periodical reports are independent from changes in value (parameter 65). 

Size: 2 Byte, Default Value: 0

Setting

Description

0

periodical reports disabled

60 - 32400

(60s-9h)

Parameter 67: External sensors - minimal change to report

This parameter defines minimal change (from the last reported) of external sensors values (DS18B20 or DHT22) that results in sending new report. Parameter is
relevant only for connected DS18B20 or DHT22 sensors. 

Size: 2 Byte, Default Value: 5

Setting

Description

0

reporting on change disabled

1 - 255

(0.1-25.5 units, 0.1)

Parameter 68: External sensors - periodical reports

This parameter defines reporting period of analog inputs value. Periodical reports are independent from changes in value (parameter 67). Parameter is relevant
only for connected DS18B20 or DHT22 sensors. 

Size: 2 Byte, Default Value: 0

Setting

Description

0

periodical reports disabled

60 - 32400

(60s-9h)

Parameter 150: Input 1 - sensitivity

This parameter defines the inertia time of IN1 input in alarm modes. Adjust this parameter to prevent bouncing or signal disruptions.Parameter is relevant only if
parameter 20 is set to 0 or 1 (alarm mode). 

Size: 1 Byte, Default Value: 10

Setting

Description

1 - 100

(10ms-1000ms, 10ms step)

Parameter 151: Input 2 - sensitivity

This parameter defines the inertia time of IN2 input in alarm modes. Adjust this parameter to prevent bouncing or signal disruptions. Parameter is relevant only if
parameter 21 is set to 0 or 1 (alarm mode). 

Size: 1 Byte, Default Value: 10

Setting

Description

1 - 100

(10ms-1000ms, 10ms step)

Parameter 152: Input 1 - delay of alarm cancellation

This parameter defines additional delay of cancelling the alarm on IN1 input. Parameter is relevant only if parameter 20 is set to 0 or 1 (alarm mode). 

Size: 2 Byte, Default Value: 0

Setting

Description

0

no delay

1 - 3600

(in seconds)

Parameter 153: Input 2 - delay of alarm cancellation

This parameter defines additional delay of cancelling the alarm on IN2 input. Parameter is relevant only if parameter 21 is set to 0 or 1 (alarm mode). 

Size: 2 Byte, Default Value: 0

Setting

Description

0

no delay

1 - 3600

(in seconds)

Summary of Contents for FIBEFGBS-222













Reviews:

No comments