background image

2.      Input  modules  type  CP−E08−M...−CL  and  CP−E16−KL−CL

2−13

Festo  P.BE−CPEA−CL−E N    en  0404NH

Incoming  CP  connection

Connect  the  incoming  CP  connection  of  the  input  modules
with  one  of  the  following  connections:

the  CP  connection  of  the  CP  master  (CP  field  bus  node,
CPX−CP  interface,  CPV  Direct,  etc.)

the  continuing  CP  connection  of  a  CP  output  module

the  CP  connection  of  a  CP  input  module  with  extended
functions

the  continuing  CP  connection  of  a  CP  valve  terminal.

Continuing  CP  connection

Connect  the  continuing  CP  connection  of  the  input  modules
with  one  of  the  following  connections:

the  incoming  CP  connection  of  a  CP  output  module

the  incoming  CP  connection  of  a  CP  input  module

the  incoming  CP  connection  of  a  CP  valve  terminal.

If  the  continuing  CP  connection  is  not  used:

·

Seal  the  CP  connection  with  a  protective  cap  type
FLANSCHDOSE  SER.712,  part  no.  356684  (accessories).
Only  in  this  way  can  you  comply  with  protection  class
IP65/IP67.

Please  note

The  continuing  CP  connection  can  only  be  used  in  conjunc
tion  with  a  CP  master  with  extended  functions.

Summary of Contents for CP-A04-M12-CL























































































Reviews: