Festo CMMS-ST-*-G2 Series Assembly And Installation Manual Download Page 8

Page: 8 / 136

Festo.P.BE-CMMS-ST-G2-HW-EN

1008NH

6.5.2

General information on EMC .............................................................. 114

6.5.3

EMC areas: second environment........................................................ 114

6.5.4

EMC-compliant wiring ........................................................................ 115

6.5.5

Operation with long motor cables...................................................... 115

6.5.6

ESD protection................................................................................... 116

Preparations for commissioning......................................................................... 117

7.1

General connection instructions........................................................................ 117

7.2

Tools / material ................................................................................................. 117

7.3

Connecting the motor........................................................................................ 117

7.4

Connecting the CMMS-ST stepping motor controller to the power supply......... 118

7.5

Connecting a PC................................................................................................. 118

7.6

Checking readiness for operation...................................................................... 118

7.7

Timing diagram switch-on sequence ................................................................. 119

Service functions and error messages................................................................ 120

8.1

Protective and service functions........................................................................ 120

8.1.1

Overview............................................................................................ 120

8.1.2

Overload current and short-circuit monitoring................................... 120

8.1.3

Voltage monitoring for the intermediate circuit ................................. 120

8.1.4

Temperature monitoring for the heat sink ......................................... 120

8.1.5

I²t monitoring..................................................................................... 121

8.1.6

Power monitoring for the brake chopper ........................................... 121

8.1.7

Commissioning status........................................................................ 121

8.2

Operating mode and error messages ................................................................ 121

8.2.1

Operating mode and error display ..................................................... 121

8.2.2

Error messages .................................................................................. 122

Technical data..................................................................................................... 128

A.1

General information........................................................................................... 128

A.2

Operation and display components................................................................... 129

A.3

Interfaces .......................................................................................................... 130

A.3.1

I/O interface [X1]................................................................................ 130

A.3.2

Increment generator input [X2] .......................................................... 131

A.3.3

CAN bus [X4] ...................................................................................... 131

A.3.4

RS232/RS-485 [X5] ............................................................................ 131

A.3.5

Motor connection [X6]........................................................................ 132

A.3.6

Power supply [X9] .............................................................................. 132

A.3.7

Increment generator interface [X10]................................................... 133

Summary of Contents for CMMS-ST-*-G2 Series









































































































































Search results

Summary of Contents for CMMS-ST-*-G2 Series

Reviews:

Brands by name

Popular brands

Festo CMMS-ST-*-G2 Series, Assembly And Installation Manual

Search results

Summary of Contents for CMMS-ST-*-G2 Series

Reviews:

Brands by name

Popular brands