manualshive.com logo in svg

Festo CMMS-ST-*-G2 Series, Assembly And Installation Manual

Share
Download
Festo CMMS-ST-*-G2 Series Assembly And Installation Manual Download Page 122

 

8. Service functions and error messages 

122  

Festo.P.BE-CMMS-ST-G2-HW-EN 

1008NH 

Display Meaning 

PH x 

Homing run. “x” represents the respective phase of the homing run: 
0: Search phase 
1: Slow moving phase 
2: Travel to zero position 
The digits are sequentially displayed 

E xxy 

Error message with index “xx” and sub-index “y” 

-xxy- 

Warning message with index “xx” and sub-index “y”. Warnings are shown at least 
twice on the seven-segment display. 

Table 

 

8.1 Operating mode and error display 

8.2.2

 

Error messages 

When a fault occurs, the CMMS-ST displays an error message cyclically in the seven 
segment display. The error message consists of an E (for error), a main index and sub-
index, e.g.: E 01 0. 
The meaning and the measures for the error messages are compiled in the table below:  

 

Error message 
Main 
index 

Sub-
index 

Meaning of error 
message 

Measures Error 

reaction 

01 

0 

Stack overflow 

Wrong firmware? 
Reload standard firmware if necessary. 
Contact Technical Support. 

PS off 

02 0 Undervoltage 

 

in intermediate circuit 

Undervoltage monitoring is configured 
using the FCT.  
Measure intermediate circuit voltage.  
Check configuration. 

PS off 

1)

 

0 Motor 

temperature 

monitoring 

Motor too hot?  
Check parameters (current regulator, 
current limits)  
Correct sensor?  
Cable broken?  
Sensor defective?  
If the error remains even when the sensor 
is bridged: device defective. 

PS off 

03 

1 Motor 

temperature 

monitoring 

Fault in dig. motor temperature sensor 

PS off 

1)

 

04 0 Over-/under-temperature 

in power electronics 

Temperature display plausible? 
Check installation conditions (cooling: via 
the housing surface, the integrated heat 
sink and back wall). 

PS off 

1)

 

Summary of Contents for CMMS-ST-*-G2 Series









































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands