manualshive.com logo in svg

Festo CMMS-ST-*-G2 Series, Assembly And Installation Manual

Share
Download
Festo CMMS-ST-*-G2 Series Assembly And Installation Manual Download Page 77

 

3. Product description 

Festo.P.BE-CMMS-ST-G2-HW-EN 1008NH 

 

77 

3.5.16

 

On-the-fly measurement 

This function offers the possibility to save the actual position value on the rising or falling 
edge of the digital input DIN9. This actual position value can then be read out for 
calculation within a controller, for example.  

 

FHPP  

PNU  350_1 

sample_position_rising_edge 

PNU  350_2 

sample_position_falling_edge 

CANopen 

 

Object 204A_05 

sample_position_rising_edge 

Object 204A_06 

sample_position_falling_edge 

 
The function is activated during configuration, and the edge to be monitored is selected. 

 

 

 

 

 
The On-the-Fly Measurement function supports continuous sampling, i.e. the configured 
edge is monitored and the stored actual position values are overwritten with each sample 
event. 

3.5.17

 

Endless positioning 

For applications such as “synchronised conveyor belt” or rotary indexing table, endless 
positioning is possible in one direction via relative positioning records. 
No endless positioning is possible in jog mode, since absolute positions are always used 
as target here. 
For relative position records, an overrun of the position counter is possible. That is, the 
position counter jumps from +32767 revolutions to -32768 revolutions, for example. 
To be able to use the Endless Positioning function, the following settings must be made 
during configuration. 

Summary of Contents for CMMS-ST-*-G2 Series









































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands