manualshive.com logo in svg

Ferris 5600001, Operator'S Manual

Share
Download
Ferris 5600001 Operator'S Manual Download Page 28

Not for 

Reproduction

26

www.ferrismowers.com | www.snapperpro.com

Installation

(IS500Z & IS1500Z Series)

(S50X & S150X Series)

 1.  Install the weight carrier (A, Figure 36) onto the 

front of the unit and secure with the 1/2-20 x 
1-1/4” bolts (B), 1/2” washers (C) and 1/2-20 nylon 
lock nuts (D).

 2.  Install the counter weights (E) in the weight carrier 

and secure with the retaining pin (F) and hairpin 
clips (G).

Figure 36.  Install Weight Carrier
A. Weight Carrier
B.  1/2-20 x 1-1/4” Bolt
C.  1/2” SAE Washer
D.  1/2-20 Nylon Lock Nut
E. Weight
F. Retaining Pin
G. Hairpin Clip

(IS2000Z Series)

 1.  Install the weight carrier (A, Figure 37) onto 

the front of the unit and secure with the 3/8-16 
x 1-1/4” bolts (B), 3/8” washers (C) and 3/8-16” 
nylock flange nuts (G).

 2.  Install the counter weights (D) in the weight carrier 

and secure with the retaining pin (E) and hairpin 
clips (F).

Figure 37.  Install Weight Carrier
A. Weight Carrier
B.  3/8” SAE Washer
C. 3/8-16X1-1/4” Bolt
D. Weight
E. Retaining Pin
F. Hairpin Clip
G.  3/8-16 Nylock Flange Nut
A.  Lower Clamp (with knob)

A

C

B

E

F

D

G

A

C

B

D

E

G

F

Summary of Contents for 5600001





































Reviews:

No comments

Brands by name

Popular brands

Load more brands