manualshive.com logo in svg

Ferris 5600001, Operator'S Manual

Share
Download
Ferris 5600001 Operator'S Manual Download Page 13

Not for 

Reproduction

11

Installation

Figure 7.  Install Blower On Deck (Notice Pin 
Orientation)
A. Blower Mount
B. Mower Deck

Preparing the Blower Mount for Assembly 

Inspecting the Blower Mount Assembly

Some blower mounts are equipped with an adjustable 
deflector bracket (A, Figure 6). If your blower mount 
is equipped with an adjustable deflector bracket it will 
need to be adjusted prior to performing the Blower 
Assembly procedure.  If not, proceed with the Blower 
Assembly procedure.

Adjusting the Blower Mount Assembly Adjustable 
Baffle

 1.  Temporarily install the blower mount (A, Figure 7) 

onto the mower deck (B).  Refer to Figure 7 for 
the position of the pins w/ lanyards in relationship 
to the chute mount bracket on the mower deck.  
The pins w/ lanyards fit into the same holes that 
the chute mount rod was installed.

 2.  Loosen the two (2) 5/16” nylock flange nuts (A, 

Figure 8) that secure the deflector bracket (B) to 
the blower mount (C).

 3.  Slide the deflector bracket up against the front 

baffle (D) of the mower deck (E) .

 4.  Tigthen the two (2) 5/16” nylock flange nuts.

 5.  Remove the blower mount and pins w/ lanyards 

from the mower deck.

A

Figure 6.  Inspecting the Blower Mount Assembly
A.  Adjustable Deflector Bracket

D

B

A

C

E

Figure 8.  Adjusting the Deflector Bracket
A.  5/16” Nylock Flange Nuts
B. Deflector Bracket
C. Blower Mount
D. Front Baffle
E. Mower Deck

B

A

Summary of Contents for 5600001





































Reviews:

No comments

Brands by name

Popular brands

Load more brands