manualshive.com logo in svg

Ferris 5600001, Operator'S Manual

Share
Download
Ferris 5600001 Operator'S Manual Download Page 20

Not for 

Reproduction

18

www.ferrismowers.com | www.snapperpro.com

Installation

Install Collector Mount Plate

Identify and follow the correct procedure for your unit.

(1000Z & IS1000Z Series)

 1.  Remove the hardware securing the rear bumper 

screen (A, Figure 24) to the top and bottom 
bumpers (A, B).  Save the 3/8” bolts and washers 
from the lower bumper.

  2  .Install the collector mount plate (Figure 25) on to 

the lower bumper and secure with the previously 
removed 3/8” bolts, 3/8” washers (B) and new 3/8-
16 nylock flange nuts (E).

 3.  Install the 3/8-16 x 1-1/2” bolts and 3/8” washers 

(C) through the top mount holes as shown in 
Figure 26.  Install the support bar (D) and secure 
with the 3/8-16 nylock flange nuts (E).

A

B

C

Figure 24.  Remove Bumper Screen
A. Screen
B. Top Bumper
C. Lower Bumper

E

D

A

B

E

Figure 25.  Install Collector Mount Plate
A. Mount Plate
B.  3/8” Bolts & Washers (previously removed)
C.  3/8-16 x 1-1/2” Bolts & 3/8” Washers
D. Support Bar
E.  3/8-16 Nylock Flange Nuts

C

Collector Installation

Summary of Contents for 5600001





































Reviews:

No comments

Brands by name

Popular brands

Load more brands