manualshive.com logo in svg

Ferris 5600001, Operator'S Manual

Share
Download
Ferris 5600001 Operator'S Manual Download Page 15

Not for 

Reproduction

13

 5.  Remove the blower belt guard and set aside.

 6.  Install the impeller drive pulley (A, Figure 11) onto 

the impeller shaft (B) as described in Figure 11.  
Install the 1/4” x 1-1/2” long key (not shown) in the 
pulley.

 7.  Align the pulley groove with the appropriate slot 

as described in Figure 11.  Tighten the set screws 
in the pulley.

 8.  Reposition the 3/8-16 x 6” bolt if required to line 

up with the pulley groove.

  9.  Check the position of the idler pulley (A, Figure 

12).  The position must be aligned with the 
position of the pulley (outer row of holes for pulley 
hub pointing in, inner row of holes for pulley hub 
pointing out).  Reposition if necessary.

Inner Slot

Align pulley groove
with slot (outer slot 
with pulley hub in 
OR inner slot with 
pulley hub out)

Figure 11.  Install Impeller Drive Pulley

Inner Row

Outer Row

Figure 12.  Check Idler Pulley Position
A. Idler Pulley

A

Hub pointing OUT:
52” Models

Hub pointing IN:
44” Models
48” Models

Installation

Outer Slot

44” Models
48” Models

52” Models

Summary of Contents for 5600001





































Reviews:

No comments

Brands by name

Popular brands

Load more brands