manualshive.com logo in svg

Ferris 5600001, Operator'S Manual

Share
Download
Ferris 5600001 Operator'S Manual Download Page 22

Not for 

Reproduction

20

www.ferrismowers.com | www.snapperpro.com

Installation

(S50X & S150X Series)

 1.  Remove the carb. shield plate from top of the rear 

bumper. 

 2.  Install the collector mount plate (A, Figure 28) 

and mount tabs (B) on to the bumper.  Install the 
3/8-16 x 1-1/4” bolts (C) and 3/8” SAE washers 
(F) through the mount tabs and loosely secure 
with the 3/8-16 nylock flange nuts (E).

 3.  Install the 3/8-16 x 1” bolts (D) and 3/8” SAE 

washers (F) through the bottom mounting holes 
and loosely secure with the 3/8-16 nylock flange 
nuts (E).

 4.  Tighten the bottom mounting bolts securely.

NOTE: All S150X models will NOT require the bottom 
mounting bolts (D, Figure 28) for installation.

 5.  Temporarily install the collector mount posts (A, 

Figure 29) into the collector plate and install the 
hitch pins (B).  This will insure that the holes are 
properly aligned for easy installation and removal.

 6.  Tighten the top mounting bolts (C, Figure 28) 

securely and remove the hitch pins and mount 
posts.

A

B

Figure 28.  Install Collector Mount Plate
A. Mount Plate
B. Mount Tab
C.  3/8-16 x 1-1/4” Bolt
D.  3/8-16 x 1” Bolt
E.  3/8-16 Nylock Flange Nut
F.  3/8” SAE Washers

B

Figure 29.  Install Mount Posts & Hitch Pins
A. Mount Post
B. Hitch Pin

A

B

E

E

C

F

D

D

C

Summary of Contents for 5600001





































Reviews:

No comments

Brands by name

Popular brands

Load more brands