Ferm FRS-600N, User Manual

Page: 3 / 34

66 Ferm
ALL PURPOSE SAW
THE NUMBERS IN THE FOLLOWING TEXT COR-
RESPOND WITH THE PICTURES AT PAGE 2
TECHNICAL SPECIFICATIONS
PRODUCT INFORMATION
Fig.A
1. Blade
2. Baseplate
3. Blade clamping screw
4. Switch
5. Speed control
6. Power cable
7. Adjusting screws baseplate length
8. Socket head wrench 4 mm (not shown)
SAFETY INSTRUCTIONS
The following pictograms are used in these instructions
for use:
Denotes risk of personal injury, loss of life or
damage to the tool in case of non-observance of the
instructions in this manual.
Denotes risk of electric shock.
Carefully read this manual before using the machine.
Make sure that you know how the machine functions and
how to operate it. Maintain the machine in accordance
with the instructions to make sure it functions properly.
Keep this manual and the enclosed documentation with
the machine.
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Keep these instructions in a safe place!
WHEN PUTTING THE MACHINE INTO OPE-
RATION:
1. Check if the switch is not in "ON" position before
you connect the mains plug to the mains voltage.
2. Always keep the power cable away from moving
parts of the tool.
SWITCH OFF THE MACHINE IMMEDIATELY
IN CASE OF
1. Malfunction in the mains plug, power cable or dama-
ging of cable.
2. Broken switch.
3. Smoke or stench of scorched insulation.
ELECTRICAL SAFETY
Always check if your mains voltage corresponds
with the value on the type plate.
The machine has been double-insulated in accor-
dance with EN 50144; therefore, an earth wire is
not necessary.
When replacing old cables or plugs
Throw away old cables or plugs immediately as soon as
new ones have replaced these. It is dangerous to put the
plug of a loose cable into the socket outlet.
When using extension cables
Only use an approved extension cable that is suitable for
the machine’s power. The cores must have a diameter of
at least 1.5 mm
2 . When the extension cable is on a reel,
unroll the cable in its entirety.
Voltage | 230 V~
Frequency | 50 Hz
Power consumption | 600 W
Number of revolutions, idle | 700 - 2300/min
Maximum saw thickness | 150 mm
Amount of travel | 26 mm
Weight | 3.5 kgs
LpA (sound pressure) | 90.4 dB(A)
LwA (sound capacity) | 103.4 dB(A)
Vibration value | 6.3 m/s 2
UK
English
Ferm 3
SPARE PARTS LIST
TOPCRAFT NR DESCRIPTION REFNR
408730 SOCKET HEAD SCREW 005
408731 HOLD DOWN PLATE 006
408732 SAW MECHANISM COMPLETE 007 T/M 10+12+15
408733 SPRING 013
408734 NEEDLE ROLLER BEARING 017
408735 BIG GEAR + PIN 019 + 020
408736 LIFTING KNIFE PLATE 023
408737 GUIDE BLOCK 025
408738 BAFFLE COMPLETE 028 + 029 + 030
408740 LOCALIZING PIN 035
408741 PENDULAR BUTTON 036
408742 THIMBLE 037
408743 SPRING 038
408744 SWITCH DRAW BAR COMPLETE 041 T/M 044
408745 CIRCUIT PLATE 046
408746 SWITCH 047
408747 STATOR 050
800607 BEARING 607 Z 051
408748 CARBON BRUSH SET 052
408749 CARBON BRUSH HOLDER 053 + 054
408750 ROTOR 055
806000 BEARING 6000 Z 056
408751 SOCKET SCREW KEY _