Service – notes on maintenance
Fig.1
Oil replacement
• Warm up engine on level ground
• Remove filler cap (8)
• Open drain plug (9) and let oil drain
completely into a pan placed under the
engine.
• Check gaskets, replace if required. Refit
drain plug and refill engine with clean oil.
• Replace filler cap.
Spark plug inspection
Fig. 3
• Disconnect the spark plug cap, and
remove any dirt from around the spark
plug area.
• Remove spark plug (17) with the plug
spanner supplied.
• Inspect the spark plug. It should be a tan
colour.
• Measure the gap (distance contact point)
with a suitable gauge. The gap should be
0,7 - 0,8 mm. Correct the gap, if necessary,
by carefully bending the side electrode.
• Replace the spark plug if the electrodes
are worn, or if the insulator is cracked or
chipped.
• Install the spark plug carefully, by hand, to
avoid cross-threading.
• Place the spark plug with correct torque:
20 Nm.
• Attach the spark plug cap.
Exhaust screen
• Wait for exhaust to cool.
• Exhaust screen may be blocked up with
carbon deposits.
• Undo the screw cap and remove the
exhaust screen.
• Clean the screen with a wire brush and
refit.
• Replace exhaust screen if damaged.
Air filter cleaning
• Remove the air filter cover (16).
• Remove filter element and wash well in
solvent.
• Pour a small amount of oil onto the filter
element and gently squeeze out any
excess oil.
• Replace the filter element and air filter cover.
• Be sure the filter cover seals properly all
around.
Do not run the engine without the air
filter element in place.
Never place a wet filter (with solvent)
on the machine.
Fuel tap
• To remove the fuel tap filter, simply undo
the cup at the bottom of the fuel tank
• Use a small spanner to remove the tap
• Clean and wash out the filter and cup, and
replace.
TROUBLESHOOTING
Basic checks
• Make sure you have plenty of fuel
• Make sure the fuel tap is on
• Make sure the engine-switch is on
• Make sure the oil level is correct
• The generator has an oil sensor. When the
oil level is too low, the generator will not be
able to start.
• Remove spark plug, connect spark plug
lead and earth it to the generator. Pull
starter cord gently and look for a spark. If
there is no spark, replace spark plug.
Spark plug is OK, but engine still won’t
start
• Check fuel tap filter is clean
• Check fuel line is clear
• Check carburetor is not clogged
Engine will not start
• Clean or replace spark plug
• Check ignition system – if faulty, contact
your service centre
• Check compression – if low, contact your
service centre
• Check for loose cylinder head – tighten
bolts
• Check for damaged cylinder head gasket –
replace if necessary
Ferax
7
• Limpie el exterior del generador y cúbralo
con una sustancia antioxidante.
• Coloque el generador en una superficie
plana y cúbralo con una tela limpia y seca.
AVERÍAS
Si se presenta una avería, por ejemplo, por el
desgaste de una pieza, póngase en contacto
con el proveedor de servicios indicado en la
tarjeta de garantía. En el dorso de este
manual encontrará un amplio resumen de las
partes de recambio que se pueden ordenar.
USO EGOLÓGICO
Para prevenir los daños durante el
transporte, el aparato ha sido embalado.
Dicho embalaje está hecho, en la medida de
lo posible, de material reciclable. Le
rogamos, por lo tanto, que recicle dicho
material.
Cualquier aparato eléctrico o
electrónico desechado y/o
defectuoso tiene que depositarse en
los lugares apropiados para ello.
GARANTÍA
Lea las condiciones de la garantía que
aparecen en la tarjeta de garantía que se
adjunta a este manual.
Declaramos, bajo nuestra única
responsabilidad, que este producto cumple
las directivas o documentos normativos
siguientes:
EN12601
de acuerdo con las directivas:
98/37/CEE
73/23/CEE
89/336/CEE
desde el 01-06-2006
ZWOLLE NL
J.A. Bakker - van Ingen
CEO Ferm BV
J. Lodewijk
Quality Manager Ferm Global
Es nuestra política mejorar continuamente
nuestros productos y por tanto nos
reservamos el derecho a cambiar las
características del producto sin previo aviso.
Servotool BV • Lingenstraat 6 • 8028 PM
Zwolle • Holanda
CE
ı
DECLARACIÓN DE CONFORMIDAD
(E)
42
Ferax
