background image

F-35-53-CE

January 2020

1

Series 35-53CE

12 VDC Microprocessor Based 

Direct Spark Ignition Control

FEATURES

Combustion blower relay with post-purge

System Diagnostic LED

Single or Multiple tries for ignition (TFI)

Multiple options for TFI, pre, inter, and post-purge timings 

Meets ANSI 60730-2-5 Harmonized Standards

Remote or local flame sensing

Standard Edge connector

Integral Standoffs for mounting

Available Manual Reset with Non-Volatile Lockout

APPLICATIONS

Recreational Vehicles (including boats/marine)

Furnace, Water Heaters

Mobile Heating Equipment

Agricultural Heaters

Construction Equipment

Process Heating and Flare Stacks

DESCRIPTION

The Model 35-53CE is a 12 VDC Microprocessor Based Direct 

Spark Ignition Control designed for use in all types of heating 

applications such as RV gas furnaces and other similar appli

-

ances. The control uses a microprocessor to continually and 

safely monitor, analyze, and control the proper operation of the 

gas burner. Value added features such as combustion blower 

control, and multiple ignition tries highlight the control's bene

-

fits. The integrated combustion blower version is fully backward 

compatible with all previous Fenwal Controls 12 VDC controls 

and competitive models. The control determines the unit con

-

figuration at the start of the heating sequence and disables the 

blower function if not required, allowing one part to address all 

service or OEM needs.

Agency Certifications

EN298 CE 584099

Classification: BMRVXN

Mobile Applications: DC supply type A, B, & C.

Code Compliant to:

AS 4625 - 2008

AS 4622 - 2004

CAN/CSA E60730-1

ANSI Z21.20: CAN/CSA C22.2 No. 60730-2-5

Compliant with current RoHS standards

SPECIFICATIONS

Input Power

Control: 9.2 to 15 VDC from a stor

-

age battery or full wave 
rectified unfiltered 50/60 Hz AC

Input Current

< 5W, 300 mA @ 12 VDC,
combustion blower and gas valve 
relays energized (control only)

Gas Valve

1.0A @ 12 VDC

Combustion Blower Rating

20.0A @ 12 VDC

Operating Temperature

-40°F to + 176°F
(-40°C to +80°C)

Flame Sensitivity

0.7 μA minimum

Flame Failure Response Time

0.8 seconds maximum

Flame Failure Lockout Time

Varies by model, 
310 seconds maximum

Flame Detector Self-check Rate

Once per second minimum

Gas Types

Natural, LP, or manufactured

Spark Rate

16 sparks per second

Size (LxWxH)

4.25 x 3.25 x 1.50 inches
(10.80 x 8.25 x 3.81 cm)

Enclosure

Uncovered with integral standoffs

Moisture Resistance

Conformal coated to operate to 
95% R.H. (Non-Condensing)
Always avoid direct exposure to 
water.

Ingress Protection

Not Rated, Protection provided by 
appliance in which it is installed

Tries for Ignition

One or Three

Trial for Ignition Periods

5, 7, 10, and 25 seconds

Pre-purge and Inter-purge 
Timings

None, 15, or 25 seconds 
depending on model. 
Without pre-purge and full-time 
power, there is a 2-second start-up 
delay.

Post-purge Timings

None, 45, 60, 90, 130, or 150 sec

-

onds available

Summary of Contents for 35-53CE Series









Reviews: