background image

Effective: January 2020

2

F-35-53-CE

SEQUENCE OF OPERATION / FLAME 

RECOVERY / SAFETY LOCKOUT

Power Up

During power up the LED shall briefly flash ON for around 1.2 

seconds, then turn OFF to indicate normal operation.

Start-Up - Heat Mode

When a call for heat is received from the thermostat, 12 VDC to 

TH, then control will begin a pre-purge delay. Following the pre-

purge period, the gas valve is energized and sparking com

-

mences for the Trial for Ignition (TFI) period.

When flame is detected during the TFI, the sparking process is 

terminated and the gas valve remains energized. The thermo

-

stat and burner flame inputs are constantly monitored to assure 

proper system operation. When the thermostat is satisfied and 

the demand for heat ends, the gas valve is immediately de- 

energized.
A post-purge delay ensures the unit is ready for the next call for 

heat.

Failure to Light - Lockout

SINGLE TRIAL MODEL

Should the burner fail to light, or a flame is not detected during 

the TFI period, the gas valve will de-energize and the control 

will go into lockout. The diagnostic LED will indicate the fault 

code for ignition lockout. (3 Flashes)

MULTI TRIAL MODEL

Should the burner fail to light or the flame is not detected 

during the TFI period, the gas valve will de-energize. The con

-

trol will then go through an inter-purge delay before an addi

-

tional ignition attempt. The control attempts two additional 

ignition trials before de-energizing the gas valve and entering 

lockout. The diagnostic LED will indicate the fault code for igni

-

tion lockout. (3 Flashes)

Flame Failure

FLAME FAILURE - RECYCLE MODE (Standard)

With the “Recycle after Loss of Flame” option, upon loss of 

flame, the gas valve is de-energized and the control proceeds 

to inter-purge before attempting to relight the flame. Multi-try 

models permit three tries for ignition including inter-purges. If 

the burner relights, normal operation resumes. If the burner 

does not relight, the control will enter lockout.

FLAME FAILURE - RE-IGNITION MODE

If the established flame signal is lost while the burner is operat

-

ing, the control will respond immediately energizing the H.V. 

spark for the TFI period in an attempt to relight the flame. If 

the burner does not light within the TFI, the gas valve will 

immediately de-energize and single try models will enter lock

-

out. On multi-try models, a new TFI sequence will begin after 

an inter-purge delay. Multi-try models perform two additional 

attempts to light the burner before de- energizing the gas valve 

and entering lockout. If the burner relights, normal operation 

resumes.

Combustion Airflow Faults

If the airflow signal is lost, or the hi-limit opens during heat 

mode, the gas valve is immediately de-energized and the 

blower stays on. If the switch closes again, a normal ignition 

sequence will resume. If not and this condition persists for 

more than five minutes, the control will enter lockout with the 

blower off.

Lockout Recovery

Recovery from lockout requires a manual reset by either reset

-

ting the thermostat, or removing power for a period of 5 sec

-

onds. On models with non-volatile lockout, reset must be by 

using the reset switch with 12VDC power maintained.

Summary of Contents for 35-53CE Series









Reviews: