Fenix 300 Usage And Installation Manual Download Page 5

5

Routine Cleaning

!

!

1

The antibacterial coating is effective when the bacteria exposed the coated 
surfaces (See the shade areas on the figure)

 

 

 

 

 

 

 

 

 

 

 

The antibacterial coating becomes not effective when the surfaces get very
dirty.

WARNING

Caution

Before you clean the unit, 
turn off the power switch.
Do not splatter  water  on 
the unit

Wear gloves when cleaning.

Clean the unit with a soft cloth.

If the unit gets very dirty, clean with a soft cloth dampened with neutral 
agent, then clean with a dry soft cloth. 

Remove the dirt from the sensor.

 (to prevent malfunction) 

Only use the neutral cleaning agents.
Do not use thinner, acidic or alkaline toilet cleaners,  or nylon 
brush.  (Otherwise,  they  may  damage  the  smoothness  of 
surface)
Only use the alcohol to clean the hand-drying area. 
(Do not use alcohol anywhere else)

Ў

Alcohol here means the alcohol used for disinfection 

  (concentration below 83%).
If the chemical cloths used, please read their instructions first.
Disinfecting agents will damage your unit.

!

Note

Draining and Cleaning the drain tank

Before it fills up (at least once a week)

The water blown off the hands is called 

drain water

.

Empty the drain water at any moment, in order to prevent 

accumulated water from exceeding the full level.

It will  start  smelling

 

 if  the accumulated water remains in 

the tank for too long time.

Pull the drain tank out in the 
horizontal direction.

This ensures the drain water 
does not splatter out.

Cleaning the exterior of unit

6

3

2

1

Routine Cleaning

1.Open the lid and empty the water.

   Pull the lid open with your fingers 
   upward, and then remove the lid 
   completely.

2.Wash out the inside of the drain tank.

3.Close the water tank lid, and re-attach 
   it to the unit as original.

   Confirm the lid is firmly inserted.

Use  the  unit  after  confirming 
that the water tank is in place.

Add 200cc 

around 1 cup

of 

water through the drain hole.

(to prevent it from getting clogged)

Cleaning the air filter

(Once every 2 months)

Press the position (shown in the figure) inward by hand, remove the front panel.

Remove the air filter

!

Note

The cotton filter can not be washed
with water.
Do not expose to the fire.

Remove the cotton 
filter elements (both 
left and right). 

Summary of Contents for 300











Reviews: