Fenix 300 Usage And Installation Manual Download Page 3

1

!

!

Dot not open the front panel.

Otherwise, This may get an electric shock.

Do not use in a wet environment, for example, near the bathroom 
where  it  may  get  the  direct  water  and  the  places  where  the 
condensation may form. 

 

 

 

 

 

 

 

 

Otherwise, this may cause electric shock and unit malfunction.

Do not allow the unit to get wet. 

Otherwise, it will cause electric shock.

Do not modify and disassemble the unit unnecessarily. 

Otherwise, this may cause fire, electric shock, or personal injury.

Ensure the unit is properly grounded.

Otherwise, may cause electric shock during malfunction or short circuit.

Installation work should be done by the qualified technician.

Incorrect wiring connection can cause electric shock and fire.

Be sure to install a residual current circuit breaker.

Otherwise, this may cause electric shock.

Use a type whose contact points are at least 3mm apart.

Please use the products of CCC standard.
Recommended ground-fault circuit breaker (for ground-fault 
protection). (Use a single-phase 2-line, AC 220V/50Hz  cable with
a 20A rated current, 15mA-type rated operating current)

Use a single-phase AC 220V/50Hz power supply.

Use within the required voltage, as voltage exceeding 220V + 10

Ј

  

will fail the unit.

Using an incorrect power supply may cause fire, electric shock and 
malfunction.

Use separate line

Using any other electric appliance with the same line, may cause the 
branch socket to become very hot and cause fire.

Turn off the power switch before inspecting and cleaning the unit. 

Otherwise, may cause electric shock.


Prohibited

Do not use in 
the bathtub or
shower room.

Do not allow 
the unit get wet. 

Prohibit 
disassembling 

Important! 
Always follow 
instructions 
closely.

Earth 
grounding 
connection

WARNING

If you don't use this unit properly or follow the 
safety  guidelines  carefully,  it  would  lead

 

to 

serious personal injury.

2

!

!

Always use the unit with the drain tank and air filter attached. 
Don't allow the water comes into the unit. 

Once water enters the unit inside, short circuit or electric shock occurs.

Wear gloves when inspecting and cleaning the unit. 

Do not attempt to install the unit with the power on (power cord).

The installation location should be strong enough to support the
unit, and the unit should be installed firmly on the surface.

Otherwise, this may cause personal injury due to the unit falling.

Wear gloves when installing the unit.

Otherwise, this may cause injury.

Otherwise, this may cause electric shock.

Otherwise, this may cause injury.

If the unit does not start, or works abnormally, turn off the power
switch

 

 and 

 

groundfault  breaker 

 

and  contact  your  dealer  for 

inspection and repair.

Otherwise, this may cause electric shock or fire due to short circuit.

Do not use in the following places:

Where the ambient temperature is below -10

 or above 40

.

Where the unit may come into direct contact with water.
Where the unit is under direct or strong sunlight.
(this may cause sensor to malfunction)
Where the condensation may form within the unit.

Safety precautions before installing the unit

Prohibited

Important!
Follow intructions

Do not let children hang from  the unit.

Otherwise, this may cause the unit to drop.

If  you  don't  use  this  unit  properly  or

 

 follow the 

safety guidelines carefully, it would lead to serious 
personal injury or property damage.
 

WARNING

Summary of Contents for 300











Reviews: