background image

SAFETY REGULATIONS

The following provides all the information necessary to 

safely operate the previously listed products of Feniex 

Industries, Inc. Please read this manual thoroughly before 

installing or operating your new product in order to 

prevent any damage or injury.  Failure to follow the listed 

instructions in this manual may result in damage to your 

products or personal injury.

•  Proper installation of this product requires good 

knowledge of automotive systems, electronics & 

procedures.

•  Please guarantee all vital components of the vehicle 

are not in danger of being damaged by drilling holes 

necessary for installation. Check all sides of the 

mounting surface before drilling any holes into the 

vehicle.

•  Do not install this product in any way that interferes 

with the deployment of the air bag. Doing so may 

damage the effectiveness of the air bag & can lead to 

serious personal and vehicle injury. The installer will 

assume full responsibility of proper installation of the 

new unit.

•  Please clean the mounting surface before installation 

of the unit when using tape, brackets, magnet, Velcro or 

suction cups.

•  The product’s ground wire must be connected directly 

to the negative (-) battery post for effective use of the 

unit. Please follow all wiring guidelines provided to 

guarantee long lifespan & productivity. Failing to follow 

these instructions may result in damage to the product.

WARRANTY

Feniex Industries, Inc. warrants to the original purchaser 

that the product shall be free from defects in material & 

workmanship for 2 years from the date of purchase for all 

Public Works products.

If warranty service is needed, please contact customer 

support:

Phone:

 1.800.615.8350 

Web Site:

 www.Feniex.com/support

Email: [email protected] 

 

If the product needs to be returned for repair or 

replacement, contact our customer service team (using 

any method listed above) to receive a Return Merchandise 

Authorization (RMA) number. Operational times are from 9 

a.m. to 6 p.m. central time, Monday through Friday.

CONDITIONS

Feniex Industries, Inc. will not be held responsible for any 

costs associated with equipment removal and/or  

re-installation resulting from a warranty claim. It is the sole 

responsibility of the party initiating a warranty claim to pay 

shipping charges associated with returning a product to 

Feniex Industries for repair or replacement.

SERVICE AFTER EXPIRATION

Feniex Industries will still provide service for all products 

after expiration of the warranty. For any issues, call the 

customer support line. In some instances it may be 

necessary for the product to be shipped, freight prepaid 

and insured for loss or damage to Feniex headquarters.

SAFETY REGULATIONS & WARRANTY

Utilizing non-factory screws and mounting brackets may result 

in the loss of warranty coverage. 

COPYRIGHT

This instruction manual and the Feniex products 

described in this instruction manual may include or 

describe copyrighted Feniex material. Laws in the United 

States and other countries preserve for Feniex Industries 

and its licensors certain exclusive rights for copyrighted 

material, including the exclusive right to copy, reproduce 

in any form, distribute and make derivative works of 

the copyrighted material. Accordingly, any copyrighted 

material of Feniex and its licensors contained herein or in 

the Feniex products described in this instruction manual 

may not be copied, reproduced, distributed, merged 

or modified in any manner without the express written 

permission of Feniex Industries, Inc.

FENIEX PRODUCT COPYRIGHTS

The products described in this document are the property 

of Feniex Industries, Inc. It is furnished by express license 

agreement only and may be used only in accordance with the 

terms of such an agreement. Products and documentation 

are copyrighted materials. Making unauthorized copies is 

prohibited by law. No part of the product or documentation 

may be reproduced, transmitted, transcribed, stored in 

retrieval system or translated into any language or computer 

language, in any form or by any means, without prior 

permission from Feniex Industries, Inc. 

Please do not send in product without contacting support first 

for a Return Merchandise Authorization (RMA) number.

TM

FENIEX //

 

INSTRUCTION MANUAL

WEB //

 

www.feniex.com

3

Summary of Contents for C-4200-DL
















Reviews: